Bosch 11335K Manual de instrucciones de uso y seguridad - Página 10
Navegue en línea o descargue pdf Manual de instrucciones de uso y seguridad para Herramienta eléctrica Bosch 11335K. Bosch 11335K 33 páginas. Operating instructions
También para Bosch 11335K: Manual de consulta rápida (25 páginas), Manual de instrucciones de uso y seguridad (28 páginas)
![Bosch 11335K Manual de instrucciones de uso y seguridad](/uploads/products/server2/1398418/1398418.png)
2610048692.qxp_11335K 10/5/17 8:51 AM Page 10
For selection of dust collection systems and
operating instructions, see the Operating /
Safety Instructions for 'Dust Extraction
unauthorized per so n nel may result in
misplacing of internal wires and
components which could cause serious
hazard. We recommend that all tool service
be performed by a Bosch Factory Service
Center or Autho rized Bosch Service Station.
TOOL LUBRICATION
Your Bosch tool has been properly lubricated
and is ready to use. It is recommended that
tools with gears be regreased with a special
gear lubricant at every brush change.
CARBON BRUSHES
The brushes and commutator in your tool
have been engineered for many hours of
dependable service.
Your tool is equipped with a Pop-out brush
system. The tool will shut off when brush
replacement, lubrication and preventive
maintenance are needed.
Only genuine Bosch replace ment brushes
specially designed for your tool should be
used.
adequate size conductors that is capable
of carrying the current necessary for your
tool must be used. This will prevent
excessive voltage drop, loss of power or
overheating. Grounded tools must use 3-wire
extension cords that have 3-prong plugs and
receptacles.
NOTE: The smaller the gauge number, the
higher the cord capacity.
Dust Extraction
Maintenance
Service
Preventive maintenance
performed
Extension Cords
If an extension cord is
necessary, a cord with
Attachments for Hammers and Hammer Drills'
included with your tool or with the dust
extraction attachment.
Every second brush change, the bearings
should be replaced at Bosch Factory Service
by
Center or Au thorized Bosch Service Station.
Bearings which become noisy (due to heavy
load or very abrasive material cut ting) should
be replaced at once to avoid overheating or
motor failure.
tool from the power supply before
cleaning or performing any main tenance.
The tool may be cleaned most effectively
with compressed dry air. Always wear
safety gog gles when cleaning tools with
compressed air.
Ventilation openings and switch levers must
be kept clean and free of foreign matter. Do
not at tempt to clean by inserting pointed
objects through openings.
plastic parts. Some of these are: gasoline,
carbon tetrachlo ride, chlo rinated cleaning
solvents,
ammonia
detergents that contain ammonia.
RECOMMENDED SIZES OF EXTENSION CORDS
120 VOLT ALTERNATING CURRENT TOOLS
Cord Size in A.W.G.
Tool's
Ampere
Cord Length in Feet
Rating
25
50
3-6
18
16
6-8
18
16
8-10
18
16
10-12
16
16
12-16
14
12
-10-
BEARINGS
Cleaning
To avoid accidents
always dis connect the
Certain cleaning agents
and sol vents damage
and
house hold
Wire Sizes in mm
Cord Length in Meters
100
150
15
30
60
16
14
0.75
0.75
1.5
14
12
0.75
1.0
2.5
14
12
0.75
1.0
2.5
14
12
1.0
2.5
4.0
–
–
–
–
–
2
120
2.5
4.0
4.0
–
–