Ancona Comfort 8 Manual de instalación y funcionamiento - Página 4

Navegue en línea o descargue pdf Manual de instalación y funcionamiento para Calentador Ancona Comfort 8. Ancona Comfort 8 5 páginas. Wall hardwire

Imprimir página
INSTALLATION (cont.)
Step 3: Marking holes for wall mount posts (Fig. 3)
Take towel warmer with four (4) Metal Wall Legs mounted, as per Step 2
-
Position against the wall where you will want to install the towel warmer
-
E
n
s
u
e r
h t
e
H
a
d r
-
-
Use light pencil to mark legs on the wall (you may want to erase the pencil mark following
installation completion, so make sure you mark lightly)
Fig. 3
Step 4: Installing wall posts (Fig. 4)
If installing on dry wall with no rear beam support (e.g. wood studs):
-
o
D
l l i r
a
h
E
n
s
u
e r
o
n I
s
e
/ t r
c s
o
P
o
t i s
o i
n
o
-
If installing on surface with rear support, e.g. wood studs (no need for Plastic Plug a)
Pre-drill small hole in the center of each circle as per step 3
o
Position Wall Post b) on top of pre-drilled hole and put in Screw c) to set in place
o
Step 5: Installing hard wire leg (Fig. 5)
-
Create a hole in the wall to let the Hard Wire Leg go through (approx. 2" x 3 3/4")
The leg will be covered by Plate h) so the hole should be large enough to allow space for
-
electrical connection and leg to go through but not too large so that the plate can cover it fully
-
Electrical wiring must be done by qualified professionals and in accordance with all applicable
codes and standards, including fire-rated constructions (refer to Electrical Requirements on Page 1)
Step 6: Mounting main body onto wall (Fig. 6)
Take main body and position each of the four (4) legs on top of the Wall Posts b)
-
Once inserted use appropriate sized Allen key to tighten each Set Screw g)
-
-
T
h
e
n i
t s
l l a
t a
o i
n
Step 7: Test the towel warmer
Remove protective white caps, they are located at the end of each of the vertical bars
-
-
Turn the switch on to start towel warmer; the On-Off switch is located at the end of one of the
posts
The towel warmer should reach its pre-set temperature in approximately 15 minutes
-
This towel warmer is designed to operate continuously and can be left on all the times. To save
-
electricity it can be turned off when not in use.
W
i
e r
L
e
g
s i
a
s l
o
u t
n r
e
d
Fig. 4
o
e l
n i
h t
e
c
e
t n
r e
f o
e
a
c
h
h t
e
d
i r
e l l
d
h
o
e l
s i
a l
g r
e
e
e r
w
h t
e
P
a l
s
c i t
P
u l
g
n i
o t
W
l l a
P
o
t s
) b
o
n
o t
p
f o
P
s
h
o
u
d l
n
o
w
b
e
c
o
m
p
e l
e t
n i
t a
9
0
d
e
g
e r
e
s
s
o
o y
u
h
f o
h t
e
o f
u
( r
) 4
i c
c r
e l
s
m
a
n
o
u
g
h
o t
n i
s
e
t r
h t
e
P
a l
s
c i t
e
a
c
h
f o
h t
e
o f
u
( r
) 4
h
o
e l
a l
s
c i t
P
u l
g
a
n
d
p
t u
n i
S
c
c
a
n
a
s l
o
m
a
k r
h t
s i
e l
g
Fig. 5
k r
e
d
o
n
h t
e
w
l l a
a
s
p
r e
S
P
u l
g
p
o r
v
d i
e
d
) a
s
e r
w
) c
o t
s
t e
n i
p
a l
c
e
Fig. 6
e t
p
3