DreamLED BML100 Manual del usuario

Navegue en línea o descargue pdf Manual del usuario para Luz exterior DreamLED BML100. DreamLED BML100 2 páginas.

Imprimir página

User's Manual

GB NL F

ILLUSTRATIONS

ILLUSTRATION 1

The DreamLED BML100 set consists of:

* 1x Garden LED Light

* 1x Ground stake

* 1x Screw + Wall plug

INSTALLING THE BATTERIES

See illustration 1

1. Remove the bottom part of the lamp by turning it in the direction of the arrow "OPEN". The battery

compartment is now visible.

2. Remove the battery compartment cover by pushing gently on the 2 closing clips at the side.

3. Insert 4x D 1.5V (LR20) Alkaline batteries (not included), observing the correct polarity inside the

lamp, on the cover and on the batteries.

4. Close the battery compartment by putting the battery compartment cover back into place. Make sure

that it is well closed and the 2 clips are "locked". Fix the bottom part by turning it in the direction of

the arrow "CLOSE".

Note:

• Remove the batteries from the product if it is not used for a long time (1 month or longer).

• For best results, you need to replace the batteries when needed: when the brightness of the LED lamp

decreases, when the light stops working or when the motion detector stops working.

INSTALLATION

The BML100 can be used anywhere and any place when you need some extra light, indoors and outdoors.

GROUND MOUNT – See illustration 2

Fix the ground stake to the BML100 by turning it in the direction of the arrow "CLOSE" and put it

into the garden ground.

FLOOR MOUNT

Place the BML100 on an even surface, like a table, the floor...

WALL MOUNT – See illustration 3

For the best results, fix the BML100 on a solid surface at a height around 1.8~2.0 m. Drill the wall

and add the wall plug and the screw. Check that the BML100 is securely fixed onto the wall!

Note:

• For outdoor installation: a location under eaves is preferable.

• Avoid installation on objects that can move/shrink/expand ...

MOTION / LIGHT SENSOR

To check that the lamp is working correctly, you can cover the lamp & sensor with your hand in a dark

place. The lamp will turn on automatically. The lamp will ONLY work when motion is detected & the

environment/location is dark.

CLEANING

Make sure the motion sensor is kept dust free and clean. Clean it regularly (1x per month) with a

dry cloth and with warm, soapy water. A dirty motion sensor may not work properly. This can lead to

premature aging of the battery and may result in unreliable operation of the device.

DECLARATION OF CONFORMITY

Hereby,

Par la présente,

Company:

TE-Group NV

Entreprise:

Address:

Kapelsestraat 61, 2950 Kapellen, Belgium

Adresse:

declare that the following equipment:

déclare que le dispositif suivant :

Product name:

DreamLED BML100

Nom du produit:

Product type:

LED Battery Motion Light

Type de produit:

conforms with the following safety requirements of the directives 2014/30/EU &

2011/65/EU. Conformity is guaranteed by the CE-symbol.

est conforme aux exigences de sécurité suivantes des directives 2014/30/EU &

2011/65/EU. La conformité est garantie par le symbole CE.

This product has been tested against following standards and specifications,

applying versions valid in September 2016.

Ce produit a été testé par rapport aux normes et spécifications suivantes,

appliquant les versions valides en Septembre 2016.

EN55015:2013 +A1:2015

EN61547:2009

Joseph van Oosterum, CEO TE-Group NV

--------------------------------Manual/BML100/09-16/V01 -----------------------------

ILLUSTRATION 2

ILLUSTRATION 3

TROUBLESHOOTING

Problem: Light flashes / low light / motion sensor does not work.

Possible solution: Weak battery. Make sure that the batteries have sufficiently capacity (if not, replace

all batteries at the same time).

SAFETY INSTRUCTIONS

• Never place the device in the vicinity of excessive heat or cold sources. Extreme temperatures have

a negative influence on the life of electronics and batteries.

• Always respect local regulations when replacing batteries.

• Protect the device from special liquids and vapors.

• Do not attempt repairs yourself.

• If the unit is not properly installed or operated DreamLED

TECHNICAL DATA

• 1x Epistar 1W Super HP LED

• Sensitivity motion sensor: max. 5~7 meters (depends on location)

• Delay time motion sensor: 15 sec. after last motion was detected

• Sensor angle: 100°

• Wide beam angle: 360° horizontal and up

• Light color: Natural white 4000K

• CRI White: Ra > 75

• IP grade: IP44 waterproof / dust proof (outdoor & indoor)

• Battery: 4x Alkaline D 1.5V (LR20) batteries

• Operating humidity: 5%~93%

• Work temperature: -10°C~+40°C

• Dimensions: 125 x 125 x 225 mm

• Weight: 975g

DISPOSAL

Dispose of electronic devices in an eco-friendly fashion! Electronic devices do not belong in your

household waste. Compliant with European Guideline 2002/96/EG for electric and electronic devices,

used electronic devices must be collected separately and taken in for environmentally sound recycling.

Options for disposing of used devices may be obtained from your township, city or municipal government.

Incorrect disposal of batteries rechargeable batteries can harm the environment! They can contain

poisonous heavy metals and are subject to treatment as hazardous wastes. Take your used batteries to

a municipal collection site.

SUPPORT

For more information, technical questions and return requests concerning this product, you should

contact: [email protected].

GUARANTEE

. DreamLED

is a registered trademark of TE-Group NV. The DreamLED

stands for superior product quality and outstanding customer service. That is why DreamLED

this product against all defects in material and workmanship for a period of two (2) years from the

date of original purchase of the product. The terms of this guarantee and the extent of responsibility of

DreamLED

under this warranty can be downloaded from the website: www.dream-led.eu.

cannot accept liability.

brand

warrants