Bosch Uneo Maxx Manual de instrucciones original - Página 6
Navegue en línea o descargue pdf Manual de instrucciones original para Herramienta eléctrica Bosch Uneo Maxx. Bosch Uneo Maxx 11 páginas. Cordless rotary hammer
También para Bosch Uneo Maxx: Manual de instrucciones original (18 páginas)
Imprimir página
OBJ_BUCH-1250-002.book Page 6 Wednesday, March 9, 2011 8:56 AM
6 | English
Cordless Rotary Hammer
Impact energy per stroke according
to EPTA-Procedure 05/2009
Tool holder
Max. drilling dia.
– Concrete (with twist drill)
– Steel
– Wood
– Wood (with spade bits Self Cut)
Weight according to
EPTA-Procedure 01/2003
Please observe the article number on the type plate of your machine.
The trade names of the individual machines may vary.
Noise/Vibration Information
Measured sound values determined according to EN 60745.
Typically the A-weighted noise levels of the product are:
Sound pressure level 85 dB(A); Sound power level 96 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values (triax vector sum) determined accord-
ing to EN 60745:
Hammer drilling into concrete: Vibration emission value
2
a
=13 m/s
, Uncertainty K=3 m/s
h
Drilling into metal: Vibration emission value a
2
certainty K=1.5 m/s
,
Screwdriving: Vibration emission value a
2
tainty K=1.5 m/s
.
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
riod.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2004/108/EC,
2006/42/EC.
Technical file at:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
2 609 004 639 | (9.3.11)
Dr. Egbert Schneider
Uneo Maxx
Senior Vice President
Engineering
J
0,6
SDS-Quick
mm
10
Robert Bosch GmbH, Power Tools Division
mm
8
D-70745 Leinfelden-Echterdingen
mm
10
08.03.2011
mm
20
Assembly
kg
1.4
Battery Charging (see figure A)
Note: The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
2
,
2
The lithium-ion battery can be charged at any time without re-
=4 m/s
, Un-
h
ducing its service life. Interrupting the charging procedure
2
does not damage the battery.
<2.5 m/s
, Uncer-
h
The lithium-ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
tomatically switched off. The battery can be damaged.
To remove the battery 10, press the battery unlocking button
18 and pull the battery out of the power tool toward the rear.
Do not exert any force.
For charging, the battery 10 can also remain in the power
tool. During the charging procedure, the power tool cannot be
switched on. Press the On/Off switch 8 to check the charge
condition of the battery, see Section "Battery Charge-control
Indication".
The battery is equipped with a NTC temperature control
which allows charging only within a temperature range of be-
tween 0 °C and 45 °C. A long battery service life is achieved
in this manner.
Observe the notes for disposal.
Selecting Tools
For hammer drilling, SDS-Quick tools are required.
For drilling without impact in wood, metal, ceramic and plas-
tic, a suitable SDS-Quick tool or an application tool with hexa-
gon shank can be used.
For screwdriving, use only screwdriver bits with ball catch 14
(DIN 3126-E6.3). Other screwdriver bits 13 can be inserted
via a universal bit holder with ball catch 12.
Dr. Eckerhard Strötgen
Head of Product
Certification
Before any work on the machine (e. g., maintenance,
tool change, etc.) as well as during transport and stor-
age, set the rotational direction switch to the centre
position. Unintentional actuation of the On/Off switch can
lead to injuries.
Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the lith-
ium ion battery of your power tool.
Do not continue to press the On/Off
WARNING
switch after the machine has been au-
Bosch Power Tools