Andis AAC-1 Manual de instrucciones de uso y mantenimiento - Página 3

Navegue en línea o descargue pdf Manual de instrucciones de uso y mantenimiento para Cortapelos Andis AAC-1. Andis AAC-1 20 páginas.

Imprimir página

BLADE TEMPERATURE

Due to the high speed nature of Andis clippers, please check for blade heat often, especially on

close cutting blades. If blades are too hot, dip the blades only into Andis Blade Care Plus or

apply Andis Cool Care Plus and then Andis Clipper Oil. If you have a detachable blade unit, you

can change your blade in order to maintain a comfortable temperature; using multiple blades of

the same size is popular among groomers.

CARE AND SERVICING OF YOUR ANDIS CLIPPER BLADES

The blades should be oiled before, during, and after each use. If your clipper blades leave

streaks or slow down, it's a sure sign the blades need oil. The clipper should be held in the

position shown in Figure D to prevent oil from getting into motor. Place a few drops of Andis

Clipper Oil on the front and side of the cutter blades (Figure E). Wipe excess oil off the blades

CLIPPING GUIDE

Description

Clipping Direction

Standard Andis Blade

With hair grain

Against hair grain

1/8" Attachment Comb

With hair grain

Against hair grain

1/4" Attachment Comb

With hair grain

Against hair grain

3/8" Attachment Comb

With hair grain

Against hair grain

1/2" Attachment Comb

With hair grain

Against hair grain

5/8" Attachment Comb

With hair grain

Against hair grain

3/4" Attachment Comb

With hair grain

Against hair grain

7/8" Attachment Comb

With hair grain

Against hair grain

1" Attachment Comb

With hair grain

Against hair grain

SNAP!

POWER SCREW

Approx. Length of Cut

Fine

Coarse

1/16" (1.6 mm)

3/16" (4.8 mm)

1/32" (0.8 mm)

1/8" (3.2 mm)

1/4" (6.4 mm)

3/8" (9.5 mm)

1/8" (3.2 mm)

1/4" (6.4 mm)

3/8" (9.5 mm)

1/2" (12.7 mm)

1/4" (6.4 mm)

3/8" (9.5 mm)

1/2" (12.7 mm)

5/8" (15.9 mm)

3/8" (9.5 mm)

1/2" (12.7 mm)

5/8" (15.9 mm)

7/8" (22.2 mm)

1/2" (12.7 mm)

5/8" (15.9 mm)

3/4" (19.0 mm)

1" (25.4 mm)

5/8" (15.9 mm)

7/8" (22.2 mm)

1-1/8" (28.6 mm)

3/4" (19.0 mm)

1" (25.4 mm)

1-1/4" (31.8 mm)

7/8" (22.2 mm)

1-1/8" (28.6 mm)

1-1/8" (28.6 mm) 1-3/8" (34.9 mm)

1" (25.4 mm)

1-1/4" (31.8 mm)

ADJUSTMENT

LEVER

OIL

with a soft, dry cloth. Spray lubricants contain insufficient oil for good lubrication, but are

an excellent clipper coolant. Always replace broken or nicked blades to prevent injury.

You can clean the excess hair from your blades by using a small brush or an old toothbrush.

To clean the blades we suggest immersing the blades only into a shallow pan of Andis Clipper

Oil while the clipper is running. Any excess hair and dirt that has accumulated between the

blades should come out. After cleaning, turn your clipper off, dry the blades with a dry cloth,

and start clipping again.

REMOVING AND REPLACING THE BLADE SET

To remove the blades, first unplug the clipper from the electrical outlet. Turn the clipper upside

down so that the blade teeth are pointing down. You may want to place the clipper on a flat

surface to do this. Unscrew the screws on the blades. Remove the blades.

To replace the blades, put the smaller, upper blade back into position (Figure F). Line up the

screw holes in the bottom blade with the two holes in the clipper housing, and replace the

screws. Do not tighten down the screws completely. Turn the clipper over and align the lower

blade so the teeth on both blades are parallel, but with the lower blade's teeth slightly above

the upper blade's teeth. Failure to do this may result in nipping the skin when cutting the hair.

FACTORY REPAIR SERVICE

When the blades of your Andis clipper become dull after repeated use, it is advised to purchase

a new set of blades available through your Andis supplier or through an Andis Authorized

Service Station.

CORRECT DISPOSAL OF THIS PRODUCT

This marking indicates that this product should not be disposed with other household

wastes throughout the EU. To prevent possible harm to the environment or human

health from uncontrolled waste disposal, recycle it responsibly to promote the

sustainable reuse of material resources. To return your used device, please use the

return and collection systems or contact the retailer where the product was purchased.

They can take this product for environmental safe recycling.

CAUTION: Never handle your Andis clipper while you are operating a water faucet and never hold your

clipper under a water faucet or in water. There is danger of electrical shock and damage to your clipper.

ANDIS COMPANY will not be responsible in case of injury due to this carelessness.