Andis AG Manual del usuario - Página 2

Navegue en línea o descargue pdf Manual del usuario para Cortapelos Andis AG. Andis AG 2 páginas. Detachable plus model ag clipper detachable blades are compatible with oster model a5
También para Andis AG: Lista de piezas (1 páginas), Especificación (2 páginas), Uso y cuidado (2 páginas)

Imprimir página

IMPORTANT SAFEGUARDS

When using an electrical appliance, basic

precautions should always be followed, including the

following: Read all instructions before using the Andis

Clipper.

DANGER:

To reduce the risk of electric

shock:

1. Do not reach for an appliance that has fallen

into water. Unplug immediately.

2. Do not use while bathing or in a shower.

3. Do not place or store appliance where it can fall

or be pulled into a tub or sink. Do not place in or

drop into water or other liquid.

4. Always unplug this appliance from the electrical

outlet immediately after using.

5. Unplug this appliance before cleaning, removing

or assembling parts.

WARNING:

To reduce the risk of burns,

fire electric shock, or injury to persons:

1. An appliance should never be left unattended

when plugged in.

2. Close supervision is necessary when this

appliance is used by, on or near children or

invalids.

3. Use this appliance only for its intended use as

described in this manual. Do not use

attachments not recommended by Andis.

4. Never operate this appliance if it has a dam-

aged cord or plug, if it is not working properly, if

it has been dropped or damaged, or dropped

into water. Return the appliance to an Andis

Service Center for examination and repair.

5. Keep the cord away from heated surfaces.

6. Never drop or insert any object into any

opening.

7. Do not use outdoors or operate with aerosol

(spray) products are being used or where

oxygen is being administered.

8. Do not use this appliance with a damaged comb

or broken blade, as injury to the skin may occur.

9. To disconnect turn control to "off" then remove

plug from outlet.

10. WARNING: During use, do not place or leave

appliance where it may be (1) damaged by an

animal or (2) exposed to weather.

SAVE THESE INSTRUCTIONS

This product is intended for Commercial Use

SERVICING OF A DOUBLE-INSULATED CLIPPER

In a double-insulated clipper, two systems of insula-

tion are provided instead of grounding. No grounding

means is provided on a double-insulated clipper, nor

should a means for grounding be added. Servicing a

double-insulated clipper requires extreme care and

knowledge of the system, and should be done only

by an Andis Authorized Service Station. Replacement

parts must be identical to those parts being replaced.

A double-insulated clipper is marked by the words

"DOUBLE INSULATION" or "DOUBLE INSULATED".

The symbol

may also be marked on the appli-

ance.

OPERATING INSTRUCTIONS

Please read the following instructions before using your

new Andis Trimmer. Give it the care that a fine precision

built instrument deserves and it will give you years of

service. Before starting your clipper remove the blade

guard (some models may not have a blade guard). Plug

cord into electrical outlet, operate 120 volt, 60 cycle AC

electrical current or as noted on unit. To start clipper

move switch button to on position, to stop, move

switch button back to original position. After using your

Andis Clipper, rewrap cord, and store in a safe place.

REMOVING BLADE SET

To remove blade set,

first make sure your

clipper motor is

switched off, then push

down on blade with

both thumbs (Diagram

A) and slide blade off

HINGE

blade hinge. If your

blade hinge should

DIAGRAM A

snap closed and is

flush with the clipper,

use a small standard

screwdriver to pry the

tongue of the hinge out

(Diagram B).

NOTE: Hair may accu-

mulate in the front

DIAGRAM B

cavity of the housing

under the blade. If this

happens, you can clean

out the hair by brushing

out the cavity with a

small brush or an old

toothbrush while the

blade is off the clipper

DIAGRAM C

(See Diagram B for

location of cavity being referenced).

REPLACING OR CHANGING BLADE SET

To replace or change your blade set, slide the blade

bracket onto the hinge of the clipper (Diagram C) and

with the clipper turned on, push the blade towards

the clipper to lock into position.

USER MAINTENANCE

The internal mechanism of your motor clipper has

been permanently lubricated at the factory. Other

than the recommended maintenance described in

this manual, no other maintenance should be per-

formed, except by Andis Company or an Andis

Authorized Repair Service Station.

CARE AND SERVICING OF YOUR ANDIS CLIPPER

BLADES

OIL

Blades should be oiled

before, during, and

after use. If your clipper

blades leave streaks or

OIL

slow down, it's a sure

sign blades need oil.

Place a few drops of

Andis Clipper Oil on the

DIAGRAM D

front and side of the

cutter blades (Diagram D). Wipe excess oil off blades

with a soft dry cloth. Spray lubricants contain insuffi-

cient oil for good lubrication, but are an excellent clip-

per blade coolant. Always replace broken or nicked

blades to prevent injury. You can clean the excess

hair from your blades by using a small brush or worn

out toothbrush. To clean the blades we suggest to

immerse the blades only into a shallow pan of Andis

Clipper Oil, while the

clipper is running. Any

excess hair and dirt that

has accumulated

between the blades

should come out. After

cleaning, turn your clip-

per off and dry blades

with a clean dry cloth

DIAGRAM E

and start clipping again.

If upon cleaning your blades you find that the blades

will still not cut, there may be a few fine pieces of hair

trapped between the upper and lower blade. If this

happens, you will need to snap the blade off the clip-

per. Proceed to slide the upper blade to one side,

without loosening the tension spring or moving the

upper blade completely out from under the tension

spring (See Diagram E for position of blade). Wipe

the surface between the blades clean with a dry

cloth, then place a drop of clipper oil where the upper

and lower blades meet and also in the guide slot of

the tension spring (Diagram E). Now slide the upper

blade to the opposite side of the lower blade and

repeat this process. After completing this cleaning

procedure, slide the upper blade centering it over the

lower blade. Handle or store your Andis Clipper with

the blades down so excess oil will not run into the

clipper case.

CAUTION: Never handle your Andis clipper while

you are operating a water faucet and never hold your

clipper under a water faucet or in water. There is

danger of electrical shock and damage to your clip-

per. ANDIS COMPANY will not be responsible in

case of injury due to this carelessness.

REPLACEMENT OF CARBON BRUSHES

WARNING: Clipper must be unplugged before

removing carbon brush caps or performing any

maintenance, as electrical shock may occur. The

carbon brushes of your clipper should be checked

every three to six months. Carbon brush replacement

should be performed

when the carbon

brushes reach no less

OIL

than 1/16" in length.

To replace the carbon

brushes, unscrew

brush caps with a

standard screwdriver.

Do one side at a time.

DIAGRAM F

Caution: The carbon brushes are spring loaded. Take

precaution when unscrewing the brush caps from the

unit (Diagram F). The brush spring should be in plain

view upon removing the cap. Pull out the spring and

brush from its canal, then remove old carbon brush.

Tip the clipper to one side so the carbon brush slides

out. Be sure to note the way the brush is inserted so

that if it does not need replacing, it may be re-insert-

TOP OF CLIPPER

CARBON BRUSH CANAL

CARBON BRUSH

INSERT BEVEL SIDE FIRST

BEVEL

DIAGRAM G

ed in exactly the same position. When placing a new

carbon brush into the carbon brush canal, make sure

to align the curvature on the end of the carbon brush

with the curve of the commutator seen at the bottom

of the canal (Diagram G). When aligned properly, the

two beveled edges of the carbon brush will be located

in the upper right and lower left corners. Be sure to

insert the beveled end of the carbon brush into the

canal first. Failure to perform this procedure correctly

may cause the carbon brushes to not seat them-

selves properly against the commutator. Replace the

carbon brush spring into the brush cavity after the

carbon brush has been installed, then replace carbon

brush cap with a standard size screwdriver. Turn

CAP

SPRING