Bosch 11387 - NA Hex 3/4" Round/Hex Demolition Hammer Manual de instrucciones de uso y seguridad - Página 8
Navegue en línea o descargue pdf Manual de instrucciones de uso y seguridad para Taladro Bosch 11387 - NA Hex 3/4" Round/Hex Demolition Hammer. Bosch 11387 - NA Hex 3/4" Round/Hex Demolition Hammer 29 páginas. Operating instructions
También para Bosch 11387 - NA Hex 3/4" Round/Hex Demolition Hammer: Lista de piezas (2 páginas)
![Bosch 11387 - NA Hex 3/4](/uploads/products/server2/1427837/1427837.jpg)
BM 1619929485 12/02
12/10/02
"VARIO-LOCK"- SELECTOR RING
The vario-lock selector ring can be set in any
one of twelve (30˚ increments) positions.
Choose a position which is best suited for
your operation. To adjust, pull the selector
ring forward and hold firmly, then turn both
the accessory and the selector ring to the
desired position. Release the selector ring
and turn the accessory slightly until it locks
in place.
"TOOL TIPS"
For the best penetration rates in concrete,
run the tool with a steady pressure, but do
not use excessive force as this will decrease
the efficiency of the tool.
Service
Preventive maintenance
WARNING
!
performed by unauth-
orized personnel may result in misplacing
of internal wires and components which
could
cause
serious
recommend that all tool service be
performed by a Bosch Factory Service
Center or Authorized Bosch Service Station.
TOOL LUBRICATION
Your Bosch tool has been properly
lubricated and is ready to use. It is
recommended that tools with gears be
lubricated with Bosch lubricant at every
brush change.
CARBON BRUSHES
The brushes and commutator in your tool
have been engineered for many hours of
dependable service. To maintain peak
efficiency of the motor, we recommend
every two to six months the brushes be
examined. Only genuine Bosch replacement
brushes specially designed for your tool
should be used.
BEARINGS
Every second brush change, the bearings
should be replaced at Bosch Factory Service
Center or Authorized Bosch Service Station.
Bearings which become noisy (due to heavy
load or very abrasive material cutting) should
3:10 PM
Page 8
All hammers require a short period of time to
warm up. Depending on the room
temperature, this time may vary from
approximately 15 seconds (90˚F) to 2
minutes (32˚F). A new hammer requires a
break-in period before full performance is
realized. This period may require up to 5
hours of operation.
An electric hammer is likely to be the most
expensive portable tool at the construction
job. The long wear and efficient operation of
the BOSCH hammers will more than justify
the cost for tools of this type. As earlier
pointed out, sharp accessories as well as
clean air vents are necessary for efficient
operation. Establish and follow a set
maintenance program.
Maintenance
be replaced at once to avoid overheating or
motor failure.
REPLACEMENT OF CORD AND
Your is designed to provide a qualified
hazard.
We
service technician optimal access to replace
the carbon brushes and the cord. This
provides the service technician the ability to
replace these components without the need
of disassembling the entire tool housing.
WARNING
!
the power supply before cleaning or
performing any maintenance. The tool may
be
cleaned
compressed dry air. Always wear safety
goggles when cleaning tools with
compressed air.
Ventilation openings and switch levers must
be kept clean and free of foreign matter. Do
not attempt to clean by inserting pointed
objects through openings.
CAUTION
!
plastic parts. Some of these are: gasoline,
carbon tetrachloride, chlorinated cleaning
solvents,
detergents that contain ammonia.
-8-
CARBON BRUSHES
Cleaning
To avoid accidents always
disconnect the tool from
most
effectively
with
Certain cleaning agents
and solvents damage
ammonia
and
household