Bosch DDS183B Manual de instrucciones de uso y seguridad - Página 4
Navegue en línea o descargue pdf Manual de instrucciones de uso y seguridad para Taladro Bosch DDS183B. Bosch DDS183B 45 páginas.
Imprimir página
BM 2610042664 DDS183 HDS183.qxp_HDS 1/4/16 1:11 PM Page 4
Use clamps or another practical way to
secure and support the workpiece to a
stable platform. Holding the work by hand or
against your body leaves it unstable and may
lead to loss of control.
Do not drill, fasten or break into existing
walls or other blind areas where electrical
wiring may exist.
unavoidable, disconnect all fuses or circuit
breakers feeding this worksite.
Always wear safety goggles or eye
protection when using this tool. Use a dust
mask or respirator for applications which
generate dust.
Use thick cushioned gloves and limit the
exposure time by taking frequent rest
periods. Vibration caused by hammer-drill
action may be harmful to your hands and arms.
Secure the material being drilled. Never
hold it in your hand or across legs.
Unstable support can cause the drill bit to bind
causing loss of control and injury.
Disconnect battery pack from tool before
making any assembly, adjustments or
changing accessories. Such preventive
safety measures reduce the risk of starting the
tool accidentally.
Position yourself to avoid being caught
between the tool or side handle and walls
or posts. Should the bit become bound or
jammed in the work, the reaction torque of the
tool could crush your hand or leg.
Use auxiliary handle(s) if supplied with the
tool. Loss of control can cause personal injury.
Hold power tool by insulated gripping
surfaces, when performing an operation
where the cutting accessory may contact
hidden wiring. Cutting accessory contacting a
"live" wire may make exposed metal parts of
the power tool "live" and could give the
operator an electric shock.
Use clamps or another practical way to
secure and support the workpiece to a
stable platform. Holding the work by hand or
against your body leaves it unstable and may
lead to loss of control.
Do not drill, fasten or break into existing
walls or other blind areas where electrical
wiring may exist.
unavoidable, disconnect all fuses or circuit
DREMEL • 2610042664 01• K/K • 5.50" X 8.50" (AMAC)
If this situation is
Safety Rules for Cordless Drill/Drivers
If this situation is
If the bit becomes bound in the workpiece,
release the trigger immediately, reverse the
direction of rotation and slowly squeeze
the trigger to back out the bit. Be ready for
a strong reaction torque. The drill body will
tend to twist in the opposite direction as the
drill bit is rotating.
Do not grasp the tool or place your hands
too close to the spinning chuck or drill bit.
Your hand may be lacerated.
When installing a drill bit, insert the shank
of the bit well within the jaws of the chuck.
If the bit is not inserted deep enough, the grip
of the jaws over the bit is reduced and the loss
of control is increased.
Do not use dull or damaged bits and
accessories. Dull or damaged bits have a
greater tendency to bind in the workpiece.
When removing the bit from the tool avoid
contact with skin and use proper protective
gloves when grasping the bit or accessory.
Accessories may be hot after prolonged use.
Check to see that keys and adjusting
wrenches are removed from the drill before
switching the tool "ON". Keys or wrenches
can fly away at high velocity striking you or a
bystander.
Do not run the tool while carrying it at your
side. A spinning drill bit could become
entangled with clothing and injury may result.
breakers feeding this worksite.
Always hold the tool with both hands. If
the bit jams two hands will give you
maximum control over torque reaction or
kickback.
Always wear safety goggles or eye
protection when using this tool. Use a
dust mask or respirator for applications
which generate dust.
Secure the material being drilled. Never
hold it in your hand or across legs.
Unstable support can cause the drill bit to
bind causing loss of control and injury.
Disconnect battery pack from tool or
place the switch in the locked or off
position before making any assembly,
adjustments or changing accessories.
-4-