Bosch 2 Manual de instrucciones original - Página 18

Imprimir página

Bosch 2 Manual de instrucciones original

1. Starting Operation

OBJ_BUCH-412-001.book Page 37 Thursday, April 3, 2008 3:18 PM

EXACT tools in another part of the assembly

process where the torque is set to 7.5 Nm, you

can use another marking ring (such as black,

blue, green or yellow) to mark the torque range

of these units. The different marking rings are

only intended as a quick reference for produc-

tion personnel to easily indentify which tool is

set for a given torque range.

Press off the marking ring 17 with a thin screw-

driver blade, a knife, or similar.

Always use the power tool with a marking ring to

insure that the housing body is sealed from dust

and dirt.

LED Indicators

Battery Condition Indicator

If the charging of the battery 11 is nec-

essary, the LED indicator 10 blinks

green and an acoustical signal sounds.

Only 6 – 8 screwing operations may be possible.

When the LED indicator lights up red, the capac-

ity is no longer sufficient for a new screw con-

nection or the power tool has been subject to

overload. The power tool can not be switched

on anymore. The start lock remains active until

the battery pack is removed from the power tool

and a charged battery pack is inserted again.

When working with a voltage adapter, the red

LED indicator 10 indicates an overload.

When the LED indicator 10 blinks red, the power

tool is overheated and can no longer be

switched on. Wait until the blinking automatical-

ly stops after a short period before continuing to

work again with the power tool.

A considerably shortened operating time of the

power tool after each charging indicates that

the battery must be replaced soon. Dispose of

the used battery in accordance with the le-

gal/country-specific regulations.

Screwing Fastener Indicator

When the preset torque is reached, the

shut off coupling responds. The LED

indicator 9 lights green.

If the preset torque is not reached, the LED in-

dicator 9 lights red and an acoustical signal

sounds. The screwing fastener must be per-

formed again.

Bosch Power Tools

Repeat Protection

When the shut-off coupling responds for a

screwing fastener, the motor shuts off. Switch-

ing on again is possible only after a 0.7 second

delay. In this manner, an unintentional re-tight-

ening of an already seated screw is avoided.

Adjusting the Angled Drive Head

ANGLE EXACT 2 | 3 | 6 | 7 | 7 – 900 | 8 |

10 – 650 | 14 – 420 | 15 | 17 |

23 | 30

The angled drive head 3 can be adjusted to a to-

tal of eight positions.

Hold the power tool with the open-end spanner 6

by the spanner flats 5 of the angled head flange.

Never clamp the tool by the housing shells!

Loosen the sleeve nut with the open-end span-

ner 4 by the spanner flats 19. Adjust the angled

drive head 3 in 45° steps to the desired position

and retighten the sleeve nut again with the

open-end spanner 4 by the spanner flats 19.

Hold the angled head flange with the open-end

spanner 6 to prevent turning.

ANGLE EXACT 14CF | 22CF | 29CF

Please observe the information of your bought-

out flat drive or inquire at your specialist shop.

Adjusting and Removing the Angled Drive

Head (see figure K)

ANGLE EXACT 25 – 250 | 30 – 380 | 40 – 280 |

50 – 210

The angled drive head 3 with tool bit holder 2

can be continuously adjusted around 360°.

Loosen the lock nut 20 by inserting an appropri-

ate tool into an opening of the lock nut and turn-

ing the lock nut in the direction of the arrow a

(left thread).

Turn the angled drive head 3 in arrow direction

b until the desired work angle is reached, but

not more than once by 360°.

Lock the angled drive head 3 in this position by

turning lock nut 20 in arrow direction c against

the angled drive head. Retighten lock nut 20

again with a tightening torque of approx. 50 Nm.

The angled drive head 3 can also be removed

completely, e.g. when it is required to replace

the marking ring 17 by one with another colour

English | 37

3 609 929 B34 | (3.4.08)