Atlantic Ultraviolet S20 Manual del usuario - Página 6

Navegue en línea o descargue pdf Manual del usuario para Sistemas de filtración de agua Atlantic Ultraviolet S20. Atlantic Ultraviolet S20 20 páginas. High capacity systems

Imprimir página

NSTALLATION

1. Remove water purifier from shipping carton. Inspect water purifier, power cord and plug for damage. Do not operate if

there is any damage to the purifier, power cord or plug.

separately. Keep the lamp aside for installation once the purifier has been properly installed.

2. Units occasionally experience damage in shipment due to the fragility of the quartz sleeve. It is, therefore, recommended

to inspect the water purifier for damage to the quartz sleeve after it has been removed from the shipping carton. Each end

of the unit as well as the inlet and outlet should be viewed to see if the quartz sleeve has experienced damage. If the

quartz sleeve shows signs of damage it should be replaced before the purifier is pressurized. See "Quartz Sleeve

Cleaning or Replacement" in the "Maintenance" section for the proper method of replacing the quartz sleeve in your

water purifier.

Note:

Solenoid plugs into the top of the Time Delay,

and the Time Delay into the Ultraviolet Monitor

COMMON

Incoming

PRE-TREATMENT or

Water

PUMPING DEVICES

Supply

1. Deionizer

2. Water Softener

3. Carbon Filters (GAC)

4. Pressure Tank

5. Pump

6. Reverse Osmosis

7. Prefilters

Ultraviolet Water Purifiers

should be installed closest

to the point of use. (POU)

3. The water purifier should be mounted horizontally on a flat dry surface. Secure the water purifier using the mounting

holes in the ballast housing or with the optional wall mounting kit. The purifier should not be solely supported by its

plumbing connections.

4. The water purifier must be connected to the cold water line only.

5. It is recommended that a 5-micron sediment filter be installed, in line, prior to the water purifier. The sediment filter will

stop or trap any particulates from entering the water purifier. Particulates may cause damage to the quartz sleeve, as well

as interfere with the purifier's ability to disinfect the water. The sediment filter may also help to reduce the amount of

routine cleaning of the quartz sleeve.

6. Shut off valves should be installed on both the inlet and outlet sides of the water purifier. The use of bypass valves is not

recommended. The shut off valves allow the purifier to be isolated from the water supply, which is required when

removing the quartz sleeve.

7. Unions should be installed on both the inlet and outlet of the water purifier; this will allow easy removal of the water

purifier from the plumbing, if required. Apply Teflon

8. When all plumbing connections are complete, allow water to enter the water purifier at a low flow rate, until the purifier

is pressurized. With the purifier pressurized, it should be checked for leaks. Once it is determined that there are no leaks,

the inlet valve can be fully opened.

9. Install lamp following the steps in "Lamp Installation or Replacement" section.

CAUTION: Lamp and quartz sleeve are easily damaged. Exercise care when installing lamp.

10. Once the plumbing hook ups are made, it is a good practice to disinfect the "downstream" plumbing between the purifier

and point of use. This is done by introducing chlorine into the purifier chamber, a 100-ppm of chlorine is suggested. With

the chlorine in the purifier chamber, turn the ultraviolet purifier on. Open the "downstream" outlet until a chlorine odor is

noticed. Close the outlet and allow the chlorine to remain in the plumbing for three (3) hours. Flush the plumbing with

ultraviolet purified water; allow the water to run for several minutes before use. This will allow the ultraviolet lamp to

reach its full germicidal output.

Figure 2 - Recommended Installation

Cold Water Line

5 Micron Filter

Valve

Union

12" Manual Wiper

50"

Recommended Minimum Clearance

For Lamp or Quartz Sleeve Removal

SANITRON

® Model S2400C is shipped with the lamp packed

(avoids ultraviolet degradation of exposed plastic pipe)

OPTIONAL EQUIPMENT

Two Minute Time Delay

Solenoid Valve

Flow Control Valve

Elbow

OPTIONAL EQUIPMENT

Ultraviolet Monitor

Audio Alarm

Wall Mounting Kit

OPTIONAL EQUIPMENT

tape to threads of inlet and outlet ports to ensure a tight seal.

Use of Metal Pipe is recommended for 12"

past elbow to the inlet or from the outlet.

POINT OF USE

(POU)

Elbow

Ultraviolet Water Purifiers

should be installed closest

to the point of use.

Outlet Line to

point of use

to be as short

as possible

Valve

Union

6" Minimum

Clearance for

Gland Access

Ultraviolet Water Purifier