Bosch 3 Manual de instrucciones original - Página 15
Navegue en línea o descargue pdf Manual de instrucciones original para Aspiradora Bosch 3. Bosch 3 22 páginas. Multifuel stove-defra exempt smokeless fuel
También para Bosch 3: Manual de instalación y uso (18 páginas), Manual de instrucciones (20 páginas), Manual de instalación, mantenimiento e instrucciones de uso (36 páginas)
Imprimir página
OBJ_BUCH-412-001.book Page 34 Thursday, April 3, 2008 3:18 PM
34 | English
Do not exert any force when inserting/re-
moving the battery. Batteries with APT con-
tact (Akku Pack Top) are designed in such a
manner that they can only be inserted into
the power tool or the charger in the correct
position.
To remove the battery 11, squeeze the locking
buttons 12 on both sides and pull the battery
downward out of the handle.
Inserting/Removing the Voltage Adapter
(see figure D)
ANGLE EXACT 2 | 3 | 6 | 7 | 8 | 14CF | 15 | 17 |
22CF | 23 | 29CF | 30
Select the voltage adapter that matches the rat-
ed voltage of your power tool.
The voltage adapters are differentiated, depend-
ing on the voltage, by the colour of the housing of
the D-sub connection plug 26. The housing of the
D-sub connection plug of 9.6 V is light blue, and
that for a voltage of 14,4-V is black in colour.
The adapter housing 28 may be mounted in
or dismounted from the industrial battery-
operated screwdriver only when the con-
stant voltage regulator is switched off or
when the connector 26 is disconnected
from the constant voltage regulator.
Move the rotational direction switch 14 to the
center position. This action locks the on/off trig-
ger switch 13 in the "off" position, which pre-
vents the tool from running.
Insert the adapter housing 28 into the handle of
the power tool. Insure that the adapter housing
is in the correct position and that the locking
buttons 12 engage securely into the handle of
the power tool.
Subsequently, plug the connector 26 of the volt-
age adapter 25 that matches your power tool in-
to the connection socket. Screw the connector
26 tightly in the connection socket 25 by tight-
ening the two screws 27 by hand.
To remove the voltage adapter, loosen the two
screws 27 on the connector 26 of the switched
off constant voltage regulator and and pull the
connector out of the connection socket 25. Sub-
sequently, squeeze the locking buttons 12 on
both sides and pull the adapter housing 28 out
of the hande of the power tool.
3 609 929 B34 | (3.4.08)
ANGLE EXACT 7 – 900 | 10 – 650 | 14 – 420 |
25 – 250 | 30 – 380 | 40 – 280 |
50 – 210
These industrial cordless screwdrivers cannot
be operated with constant voltage regulator.
Changing Application Tools on the Head
with Quick-change Chuck (see figure E)
When working with an application tool, pay
attention that the application tool is firmly
seated on the tool holder. When the applica-
tion tool is not firmly connected with the tool
holder, it can come loose again and not be
controlled.
ANGLE EXACT 2 | 3 | 6 | 7 – 900
A straight screw head with 1/4" quick-change
chuck (Article number 0 607 453 631) is availa-
ble for these industrial cordless angle wrenches.
ANGLE EXACT 2 | 3 | 6 | 7 | 8 | 15
An angled screw head with 1/4" quick-change
chuck (Article number 0 607 452 630) is availa-
ble for these industrial cordless angle wrenches.
Inserting
Pull the quick-change chuck 29 to the front. In-
sert the tool 1 into the tool holder 2 and release
the quick-change chuck.
Use only insertion tools with fitting end pieces
(1/4" hexagonal).
Do not attempt to insert quick-change type drill
bits into this chuck.
Industrial cordless angle wrenches with shut-off
clutches are not suitable for drilling applica-
tions. The clutch can shut off automatically and
without warning. When continuing to drill after
the clutch has shut off, the power tool can break
free until the shut-off clutch engages again, and
lead to loss of control.
Removing
Pull the quick-change chuck 29 to the front.
Take the tool 1 out of the tool holder 2 and re-
lease the quick-change chuck.
Bosch Power Tools