Bosch 4 V-LI Manual de instrucciones original - Página 7
Navegue en línea o descargue pdf Manual de instrucciones original para Aspiradora Bosch 4 V-LI. Bosch 4 V-LI 10 páginas. Professional
También para Bosch 4 V-LI: Manual de instrucciones (31 páginas), Manual de instrucciones original (7 páginas), Manual de instrucciones original (7 páginas), Manual de instrucciones original (48 páginas), Manual de instrucciones original (14 páginas), Manual de instrucciones original (15 páginas)
Imprimir página
OBJ_BUCH-832-004.book Page 15 Wednesday, December 12, 2012 10:31 AM
Cordless Impact Screwdriver
Article number
Rated voltage
No-load speed
Impact rate
Maximum torque, hard screwdriving
application according to ISO 5393
– ¼" hexagon socket
– ½"
Bolt size
Tool holder
Weight according to EPTA-Procedure
01/2003
* Value dependent of the battery pack being used
Noise/Vibration Information
Measured sound values determined according to EN 60745.
Typically the A-weighted noise levels of the product are:
Sound pressure level 96 dB(A); Sound power level
107 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a
(triax vector sum) and uncertainty K
h
determined according to EN 60745:
Impact tightening of fasteners of the maximum capacity of the
2
2
tool: a
=12 m/s
, K=1.5 m/s
.
h
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
riod.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep hands warm, organise work patterns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Bosch Power Tools
GDX 14,4 V-LI
3 601 JB8 0..
V=
-1
min
-1
min
Nm
Nm
mm
¼" hexagon socket
kg
Dr. Egbert Schneider
Senior Vice President
Engineering
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
16.11.2012
Assembly
Battery Charging
Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the lith-
ium ion battery of your power tool.
Note: The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The Lithium-Ion battery can be charged at any time without
reducing its service life. Interrupting the charging procedure
does not damage the battery.
The Lithium-Ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
Do not continue to press the On/Off switch after the
machine has been automatically switched off. The bat-
tery can be damaged.
The battery is equipped with a NTC temperature control
which allows charging only within a temperature range of be-
tween 0 °C and 45 °C. A long battery service life is achieved
in this manner.
Observe the notes for disposal.
Removing the battery
The battery 5 is equipped with two locking levels that should
prevent the battery from falling out when pushing the battery
unlocking button 6 unintentionally. As long as the battery is
inserted in the power tool, it is held in position by means of a
spring.
14.4
0 –2800
0 –3200
150*
170
M6 – M16
¼" hexagon socket
/ ½"
1.5/1.7*
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
1 609 92A 00R | (12.12.12)
English | 15
GDX 18 V-LI
3 601 JB8 1..
18
0 –2800
0 –3200
160*
180
M6 – M16
/ ½"
1.6/1.8*