3M 6240811 Instrucciones de cambio - Página 2

Navegue en línea o descargue pdf Instrucciones de cambio para Sistemas de filtración de agua 3M 6240811. 3M 6240811 12 páginas.

Imprimir página

Read entire manual: Failure to follow all guides and rules could cause personal injury or property damage.

• Check with your local public works department for plumbing codes. You must follow their guidelines as you install the Water Filtration system.

• Your Water Filtration system will withstand up to 125 pounds per square inch (psi) (862 kPa; 8,62 bar) water pressure. (100 psi (689 kPa; 6,89 bar) for B1175H-S &

B1175-S only). If your water supply pressure is higher than 80 psi (552 kPa; 5,52 bar), install a pressure reducing valve before installing the Water Filtration system.

To reduce the risk associated with choking:

• Do not allow children under 3 years of age to have access to small parts during the installation of this product.

To reduce the risk associated with the ingestion of contaminants:

• Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

To reduce the risk associated with property damage due to water leakage or ﬂ ooding:

• Read and follow Use Instructions before installation and use of this system.

• Change the disposable ﬁ lter cartridge at the recommended interval; the disposable ﬁ lter cartridge MUST be replaced every 12 months or sooner.

• Failure to replace the disposable ﬁ lter cartridge at recommended intervals may lead to reduced ﬁ lter performance and failure of the ﬁ lter, causing property damage from

water leakage or ﬂ ooding.

• Protect from freezing, remove ﬁ lter cartridge when temperatures are expected to drop below 40° F (4.4° C).

• Do not install systems in areas where ambient temperatures may go above 100° F (38° C).

• Do not install on hot water supply lines. The maximum operating water temperature of this system is 100°F (38°C).

• Do not install if water pressure exceeds 125 psi (862 kPa; 8,62 bar). (100 psi (689 kPa; 6,89 bar) for B1175H-S & B1175-S only). If your water pressure exceeds 80 psi (552

kPa; 5,52 bar), you must install a pressure limiting valve. Contact a plumbing professional if you are uncertain how to check your water pressure.

CARTRIDGE CHANGE INSTRUCTIONS

STEP 1

Turn cartridge slowly to the left, about 1/4 turn, until it stops (when

arrows line up). At this position, both inlet and outlet ports are closed &

water pressure has been relieved. Inlet water will automatically turn off.

STEP 2

Pull used cartridge straight down & discard.

Note: There may be a small amount of residual water drainage after

pressure is relieved and during cartridge removal.

STEP 3

Remove sanitary cap from top of new

cartridge. Moisten o-ring with water and push new cartridge into

ﬁ lter head. Turn cartridge 1/4 turn to the right until it stops. Top

surface of cartridge will become ﬂ ush with bottom of the head when

fully engaged. The label should be facing forward.

STEP 4

Inlet water will automatically turn on. Flush new ﬁ lter cartridge in

accordance with Performance Data Sheet expelling any trapped air

and carbon ﬁ nes. Water may run cloudy with air but will quickly clear.

System is now ready for use.

STEP 5

Complete water hardness test as per water hardness test kit instruc-

tions provided with new cartridge. The water sample used for com-

pleting the water hardness test should be taken upstream before the

location of the new 3M™ ScaleGard™ Blend product. If your site is a

new build, the water sample used for completing the water hardness

test should be taken at a nearby existing site.

STEP 6

Based on water hardness test results (Step 5), set blend setting in head as per

the food service application tables (see pages 3 - 11).

WARNING:

NOTICE: