ELEKTRA Nivola W Manual de formación - Página 4
Navegue en línea o descargue pdf Manual de formación para Cafetera ELEKTRA Nivola W. ELEKTRA Nivola W 6 páginas.
Imprimir página4.ASSEMBLY
1.
Place plastic drip tray
into position.
2.
Place metal drip tray cover
into plastic drip tray.
The indicator lamps
•
The green light — indicating
the power switch is on and
that power is available to the
machine. This light is on during
all phases of the machine's
operation.
•
Red stand-by light.
This light shows that the water
in the boiler is not at the
correct temperature to make
coffee. It will come on when
the machine is first turned on
and turn off when the boiler
has reached the correct
operating temperature.
Thereafter it will light if the
boiler is not up to temperature
when either the steam or
coffee functions are selected.
Clock
To remove the clock:
•
carefully twist the plastic cover
clockwise to remove.
•
gently prise clock assembly
from Nivola. The clock is a
push-fit.
5.OPERATING INSTRUCTIONS
Preparing
The following procedure must be
carried out when the Nivola is
the Nivola for first
being used for the first time, or if it
time use
has not been used for some time.
This procedure primes the water
circuit, including the pump.
06
3.
Place filter basket into coffee
handle.
4.
Attach coffee handle to group
head.
•
Red water level warning light.
Comes on if the reservoir
water level is too low.
A buzzer will also sound.
Fill the reservoir with fresh,
cold water to within two
centimetres of the top.
Red
Red
Stand-by indicator.
Water level in
reservoir is too
Boiler water is not
low. Fill reservoir.
up to correct
temperature.
Green
Power on indicator.
To change the time, remove the
plastic sleeve from around the
clock to expose the adjusting
knob. The clock's battery is acces-
sible from the back of the clock.
When replacing the plastic cover,
align the clips correctly to the
slots (there's only one way they
line up), then gently turn the cover
anticlockwise.
5.OPERATING INSTRUCTIONS
1.
With machine switched off
at its power switch, plug
machine into power outlet and
turn on at power outlet.
Do not turn on power
at machine's on-off switch.
2.
Remove cup heating tray and
fill reservoir with cold fresh
water to about two centime-
tres below the rim.
3.
Immerse steam wand in a
container of cold water so its
two steam outlet holes are
covered by the water.
The breather hole on the top
should be uncovered.
4.
Turn control knob anticlock-
wise to the steam position.
5.
Turn on the machine at its on-
off switch. The indicators will
light and the buzzer will sound
for five seconds to indicate the
boiler is empty. The machine
will then go through a 24 sec-
ond start cycle to prime the
water circuit. When the cycle is
finished, the red stand-by light
will go out.
6.
Turn the control knob to the off
position. The red stand-by light
will come on, indicating the
machine is heating the water
in the boiler in preparation for
making coffee.
Regular use
1.
Remove cup heating tray.
2.
Fill reservoir with fresh cold
water to about two centime-
tres below the rim.
3.
Ensure control knob is OFF
(middle setting).
07
7.
When the boiler reaches its
correct operating temperature
the stand-by light will go out,
indicating that the machine is
ready to make coffee.
power on-off
switch should
be OFF
(outwards
position)
small breather
hole
steam outlet
holes
steam
Press ON
4.
Turn power on at power outlet.
5.
Turn machine on at its on-off
switch.
6.
When the red stand-by light
goes out, the machine is
ready to make coffee.