Daikin R32 Split Series Manual de instalación - Página 8

Navegue en línea o descargue pdf Manual de instalación para Ventilador Daikin R32 Split Series. Daikin R32 Split Series 14 páginas. R32 split series
También para Daikin R32 Split Series: Manual de instalación (17 páginas), Manual de instalación (16 páginas), Manual de instalación (16 páginas), Manual de instalación (16 páginas), Manual de instalación (17 páginas), Manual de instalación (16 páginas), Manual de instalación (20 páginas), Manual de instalación (14 páginas), Manual de instrucciones (16 páginas), Manual de instrucciones (16 páginas), Manual de instrucciones (8 páginas), Manual de instalación (17 páginas), Manual de instalación (16 páginas), Manual de instalación (20 páginas), Manual de instalación (20 páginas), Manual de instalación (16 páginas), Manual de instalación (16 páginas), Manual de instalación (14 páginas), Manual de instalación (14 páginas), Manual de instalación (16 páginas), Manual de instalación (17 páginas), Manual de instalación (20 páginas), Manual de instalación (13 páginas)

Imprimir página

Daikin R32 Split Series Manual de instalación

Indoor Unit Installation

3-2. Left-side, left-back, or left-bottom piping

How to switch around the drain plug and drain hose

1) Remove the ﬁxing screw and

pull out the drain hose.

1 Remove ﬁxing

1) Switch around the drain plug and drain hose.

2) Attach the drain hose to the underside of the refrigerant

pipes with adhesive vinyl tape.

3) Shape the refrigerant pipes along the pipe path marking

on the

4) Pass the drain hose and refrigerant pipes through the

wall hole, then position the indoor unit on the

plate hooks, using the

unit as a guide.

5) Open the front panel, then open the service lid. (Refer to

"Service lid" on page 4.)

6) Pass the inter-unit wire from the outdoor unit through the

feed-through wall hole and then through the back of the

indoor unit. Pull them through the front side. Bend the ends

of tie wires upward for easier work in advance.

(If the inter-unit wire ends are to be stripped first, bundle

wire ends with adhesive tape.)

7) Connect the refrigerant pipes.

8) In case of pulling the drain hose through the back of the indoor

unit, wrap the refrigerant pipes and drain hose together with

insulation tape as shown in the figure.

9) Press the bottom frame of the indoor unit with both hands until it is

firmly caught by the

wires do not catch on the edge of the indoor unit.

3-3. Wall embedded piping

Follow the instructions given under left-side, left-back, or

left-bottom piping.

1) Insert the drain hose to a depth of 1-15/16 inches (50mm)

or more so it will not be pulled out of the drain pipe.

Wiring

Refer to the installation manual for the outdoor unit also.

WARNING

• Do not use tapped wires, extension cords, or starburst connections, as they may cause overheating, electric shock, or fire.

• Do not use locally purchased electrical parts inside the product. (Do not branch the power for the drain pump, etc., from the

terminal block.) Doing so may cause electric shock or fire.

• Do not connect the power wire to the indoor unit. Doing so may cause electric shock or fire.

3) Switch around the drain hose and drain plug.

Drain plug

screw.

Drain hose

Pull out

drain hose.

Insert a hexagonal

2) Pull out

wrench (3/16 inch (4mm)).

drain plug.

mounting plate.

markings at the top of the indoor

mounting plate hooks. Make sure that the

Push the drain plug all the

way in using a hexagonal

wrench (3/16 inch (4mm)).

Hexagonal wrench

(3/16 inch (4mm))

Do not apply lubricating oil

(refrigerant oil) to the drain

plug when inserting it.

The application of lubrication

oil to the drain plug will

deteriorate the plug to cause

drain leakage from the plug.

Remove pipe port cover here for

left-bottom piping.

mounting

Drain

hose

Caulk this hole

with putty or

caulking material.

Bottom frame

Secure the indoor unit to the

indoor unit ﬁxing screws M4 × 1/2" (M4 × 12mm)(2 points).

Insert the drain hose

to this depth so it will

not be pulled out of

the drain pipe.

Insert drain hose securely

and ﬁx in place with ﬁxing

screw.

Fixing screw

Drain hose

Left-bottom piping

Wrap

Bind with

around the bent portion

adhesive

of refrigerant pipe.

vinyl tape.

Overlap at least half the

width of the tape with

each turn.

Drain hose

Refrigerant

pipes

mounting plate with the

Inner wall

1-15/16"

Drain hose

(50mm)

or more

Vinyl chloride

Outer wall

drain pipe (VP-30)

φ1-3/16" (30mm) or more

Remove pipe port

cover here for

left-side piping.

Left-side piping

Left-back piping

A Mounting

plate

insulation tape

Mounting

plate

■

English