DSC Envoy NT9010 Manual del usuario - Página 8

Navegue en línea o descargue pdf Manual del usuario para Sistema de seguridad DSC Envoy NT9010. DSC Envoy NT9010 20 páginas. Demo stand
También para DSC Envoy NT9010: Instrucciones de instalación (4 páginas)

Imprimir página

Section 1: Introduction

Your installer has set up your system with your home or business in mind. You may

not need all of the features described in this manual. Your installer will only turn

on the features that you need, and should explain all the active features to you. If

you have any questions about which features are included on your system, please

ask your installer.

How Your

Your security system consists of a DSC NT9010 controller, and various detectors

System Works

and wireless devices.

The controller is the "brain" of your security system. It controls and checks all the

detectors, and communicates with the central station (if remote monitoring is

enabled). You will access system functions with your NT9010 controller, which is

Ready

Armed

System

Stay

Away

described on pages 2 and 3 of this manual. Each NT9010 has a microphone, siren,

Chime

Exit

Status

Volume

speaker, number pad, emergency keys, and eight function keys.

Record

Playback

Using the NT9010 you can send commands to the system and check the current

system status. Your installer will mount the NT9010 in a convenient location inside

your premises.

Your security system can provide monitoring of intrusion, fire, and emergency.

The security system has several zones (monitored areas). Each of these zones will

be connected to a detector (motion detector, glassbreak detector, door contact,

etc.). If a detector goes into alarm, the NT9010 will sound an alarm and may

announce the specific zone that caused the alarm (depending on how your

installer has programmed the system).

IMPORTANT

A security system cannot prevent emergencies. It is only intended to alert

NOTICE

you and – if the system is remotely monitored – your central station of an

emergency situation. Security systems are generally very reliable but they

may not work under all conditions and they are not a substitute for pru-

dent security practices or life and property insurance. Your security system

should be installed and serviced by qualified security professionals who

should instruct you on the level of protection that has been provided and

on system operations. For important warnings and cautions, please see

page 34.

Glossary

Access code

A 4- or 6-digit code you enter on the keypad to turn your system on or off, or to

use other system features.

Alarm

When a zone is violated (e.g., a smoke detector detects smoke, a motion detector

senses movement, a door with a contact is opened), it will trigger an alarm.

Intrusion (burglary) alarm: An alarm triggered by an intrusion detector (e.g.

motion detectors, glassbreak detectors, door/window contacts). Usually occurs

when the system is on. Intrusion alarms sound with a steady siren.

Fire alarm: An alarm triggered by fire, smoke or heat detectors. Fire alarms may

be triggered at any time, whether the system is on or off. Fire alarms sound with a

pulsing siren.

Announce

Voice notification by the NT9010 of a variety of system conditions.

Audible exit

A feature that warns you of an improper exit (e.g. door not completely shut) when

fault

you attempt to turn on your system. Helps to prevent false alarms.

Away arming

Turning on the system so that all the detectors (perimeter and interior) are on.

(Used when everyone is away from the premises.)

Bypassing a

Turning off a detector temporarily. When you bypass a zone, the detector for that

zone

zone will not monitor activity in the zone and will not be able to trigger an alarm,

until the system has been turned off, then on again.

Central

If remote monitoring is enabled, your system will send alarms, troubles and emer-

station

gency messages to the central station. If necessary, the central station will then

notify authorities in your area.

Detector

A part of the system that can detect and report problems (e.g. a motion detector

can tell if there is movement in a room).

Emergency

A message sent to the central station when one of the 3 pairs of emergency keys

message

(

) is pressed and held for two seconds. Your installer must program these

keys, or they will not work.

Entry time

A timer programmed by your installer. It starts when you enter an area of the sys-

tem that is on. You must enter an access code to turn the system off before the

timer runs out, or else an alarm will be triggered.