Ansell APLEDDVRL Instrucciones de instalación

Navegue en línea o descargue pdf Instrucciones de instalación para Linterna Ansell APLEDDVRL. Ansell APLEDDVRL 2 páginas. 8w 4000k profile led dual voltage razor light

Imprimir página

General Installation Instructions

These instructions should be read carefully prior to any installation and retained after completion for further

reference and maintenance. Please give these instructions to the building owner/occupier after installation.

Important Safety

Before installation, maintenance or lamp replacement, ensure that the mains supply to the luminaire is switched off and the circuit supply fuses are removed or

the circuit breaker is turned off.

It is recommended that only a qualified electrical contractor carries out the installation of this luminaire and that the luminaire is installed in compliance with the

current edition of the IEE Wiring Regulations.

The person carrying out the installation is to check and verify that the total load on the circuit, including that of this luminaire does not exceed the rating of the

circuit cable, fuse or circuit breaker.

Where a luminaire incorporates discharge control gear (inductive load), the circuit capacity and ratings require careful sizing to avoid nuisance tripping of the

protective device used in the installation.

Where applicable, careful consideration should be taken during installation to ensure that all fixings and/or suspensions are of a suitable size for the luminaire

being installed.

Ratings

1. All luminaires are manufactured & tested in compliance with the requirement contained within BS EN 60598 and are CE marked.

2. All luminaires that are of Class 1 construction and that are marked accordingly, MUST be earthed.

3. All luminaires are designed to operate at 230Volts AC -6%/+10% = 216Volts to 252Volts. Do not operate outside these voltages.

4. All luminaires are only suitable for applications within their rated Ingress Protection limits as stated

5. The safety isolating transformer specified for this product has a load of 20VA max at both 110V and 230V.

Exclusions to Warranty

Please Note - The limited warranty shall be null and void in the following circumstances:-

Failure by the installer, end user or any third party to exercise caution to protect any covered product or part from outside damage, adverse temperature (normal

operating ambient temperature 0 - 25°C), humidity conditions, fluctuations in the electrical system or physical abuse as well as failure related to workmanship in the

installation of the products or parts.

-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

INSTALLATION



Select a suitable mounting surface and provide a suitable power supply.



This luminaire is IP20 and must be installed within the correct area within a bathroom application in accordance to the latest edition of BS

EN 7671.



The luminaire must be mounted horizontally only.



Remove the luminaire cover/diffuser by depressing the diffuser and pulling away.



Remove the protective cover at the rear of the fixture by removing the two screws.



Offer the luminaire to the mounting surface and fix to a suitable surface taking care not to foul any piping or cables beneath the surface.



Connect the mains supply making sure the correct polarity is observed. Please see connections below.

Electrical Connection

Connect as follows:-

SWITCHED LIVE

EARTH

NEUTRAL

Remote Switching



Replace the cover at the rear of the fixture using the two screws previously removed.



Fix the luminaire to the mounting surface.



Replace the diffuser. Please note the luminaire will NOT function without the diffuser being installed.



Restore the supply and test for satisfactory operation.

---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

1. This luminaire contains no serviceable parts.

Disposal of Electronic Equipment WEEE Directive 2002/96/EC

This product falls within the scope of the Waste Electrical & Electronic Equipment Directive

(WEEE), which means the product should not be disposed of as normal household waste.

Ensure that this luminaire and lamp is disposed of in accordance with the WEEE Directive.

Contact a local Council Waste Dept. Local Amenity Site, or the Environment Agency for

further information. RoHS - All components and materials used in this product are RoHS

2002/95/EC compliant.

-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Page No. 1

Description –

Installation Instructions

Luminaire Code(s) –

(L)

BROWN (switched)

(E)

GREEN / YELLOW

(N)

BLUE

(RS)

BLACK x 2

www.anselluk.com

8W 4000K Profile LED Dual Voltage

Razor Light

APLEDDVRL

Blue / Black

Brown / Red

Issue Date: td 20150121