DSC Envoy NT9010DMK Instrucciones de instalación

Navegue en línea o descargue pdf Instrucciones de instalación para Control Panel DSC Envoy NT9010DMK. DSC Envoy NT9010DMK 4 páginas. Desk mount

Imprimir página

™

1. Locating the NT9010DMK

Choose a location close to a telephone outlet. The phone

cables provided are 6ft long.

2. Wiring the Phone Cables and AC (see Diagram 1)

Pull out the drawer to access the opening in the bot-

tom of the Desk Stand.

Run the phone cable(s) and the AC wire from back to

front through the opening in the Desk Stand.

Connect the AC wires to the two terminals labeled as

AC.

Connect the red wire of the phone cable to the RING

terminal and green wire to the TIP terminal on the

Desk Stand.

If you wish to connect a telephone to the Envoy, take

the second phone cable provided and connect the red

wire of the cable to the R1 terminal and the green

wire to the T1 terminal on the Desk Stand. This will

provide telephone line seizure if you are on the phone

connected to the system and an alarm occurs.

Push the phone cable(s) and the AC wire into the wir-

ing channels on the bottom of the Desk Stand.

3. Mounting the Desk Stand to the NT9010 (see

Diagrams 2, 3 & 4)

•

Remove the Wall Mount plate from the NT9010 by follow-

Diagram 2

ing steps in

Remove the plastic screw from the backplate.

Insert a flathead screwdriver into the slots and

twist to release the backplate

Pull the backplate away from the Envoy and remove

the posts.

•

Insert the 2 round posts of the desk stand into the back of

NT9010 as shown in step

•

With the back of the Desk Stand facing you, push down on

the Desk Stand with your thumbs as shown in step

Diagram 4

, until you hear two clicks. The Desk Stand will

now be properly secured to the NT9010.

NOTE:

Please make sure that the battery is connected

before completing this step.

•

Once this is completed and the unit is in its desired loca-

tion, plug the phone cable connected to TIP and RING into

the wall outlet and connect the other phone cable to the

telephone (if applicable).

•

Now that the unit is set up, apply AC power, set up devices,

and complete all programming as described in the NT9010

manuals.

Diagram 3

firealarmresources.com

Desk Mount NT9010DMK

Removing the Desk Stand from the unit

(see Diagram 5)

•

Unplug the AC transformer and phone cable(s).

•

Take the mounted NT9010 and stand it in its upright posi-

tion.

•

Grab the portion of the Desk Stand that is pointing

upwards.

•

Pull the Desk Stand upward to release the catches that hold

the Desk Stand to the NT9010.

•

Pull the Desk Stand away from the NT9010 and remove the

Desk Stand posts from the NT9010.

Limited Warranty

Digital Security Controls Ltd. warrants that for a period of 12 months from the date of

purchase, the product shall be free of defects in materials and workmanship under

normal use and that in fulfilment of any breach of such warranty, Digital Security Con-

trols Ltd. shall, at its option, repair or replace the defective equipment upon return of

the equipment to its repair depot. This warranty applies only to defects in parts and

workmanship and not to damage incurred in shipping or handling, or damage due to

causes beyond the control of Digital Security Controls Ltd. such as lightning, exces-

sive voltage, mechanical shock, water damage, or damage arising out of abuse, alter-

ation or improper application of the equipment.

The foregoing warranty shall apply only to the original buyer, and is and shall be in

lieu of any and all other warranties, whether expressed or implied and of all other

obligations or liabilities on the part of Digital Security Controls Ltd. Digital Security

Controls Ltd. neither assumes, nor authorizes any other person purporting to act on

its behalf to modify or to change this warranty, nor to assume for it any other war-

ranty or liability concerning this product.

In no event shall Digital Security Controls Ltd. be liable for any direct, indirect or con-

sequential damages, loss of anticipated profits, loss of time or any other losses

incurred by the buyer in connection with the purchase, installation or operation or

failure of this product.

Warning

: Digital Security Controls Ltd. recommends that the entire system be

completely tested on a regular basis. However, despite frequent testing, and due to,

but not limited to, criminal tampering or electrical disruption, it is possible for this

product to fail to perform as expected.

Important Information

by Digital Security Controls Ltd. could void the user's authority to operate this equip-

ment.

Installation Instructions

: Changes or modifications not expressly approved

29005753 R001