DSE DK-PV500LW Manual del usuario - Página 2

Navegue en línea o descargue pdf Manual del usuario para DVR DSE DK-PV500LW. DSE DK-PV500LW 5 páginas. Portable digital video recorder

Imprimir página

OWNER'S MANUAL

Inserting SD card - Before turning on the DVR, the first thing to do is to install the SD card.

Without SD card DVR does not start.

E 'comes with the product a micro SD card to 16 GB. E 'but you can use any micro-SD card up to

32GB capacity.

The SD card is inserted into the side (11). The insertion position is rendered unique by the shape

of the card. It should push the SD card in its seat until you feel the engagement.

To remove the SD card, push the nail up to unhook it and then pull it out. The DVR will

automatically format the SD card when inserted for the first time. If necessary, you can format it

by the APP as described below.

It is never necessary to format the SD card using a PC before inserting it into the DVR.

Charger - Before using the equipment it is advisable to charge the battery for a few hours.

Connect the power supply to the DC input IN and verify that the green LED turns on charging.

The green LED turns off when fully charged.

Connection with dedicated cameras RE-TCN9XH and DK-TCN9CH - The digital video

recorder is designed for DK-PV500LW

work with its cameras

analog to wear which must be connected to the jack minijack CAMERA IN (1)

In this way the DVR picks up the signal A / V digital camera and provides you with contextually

power.

Connection with generic analog cameras

The digital video recorder DK-PV500LW can also work with any CVBS analog camera, to

connect an analog video source to the DVR using the cable supplied with the white RCA (audio)

and yellow (video). The adapter cable plugs in the same minijack CAMERA IN (1).

Note that if you use generic cameras, the DVR can not provide power supply for which it will be

necessary to feed the camera separately.

PC Connection - The DK-PV500LW can be connected to PC so that movies and images saved

on the SD card can be easily downloaded to your computer.

For connection to a PC using the supplied USB cable and the USB port (8) on the unit. The DVR

must be connected to the PC turned off, so no light is ON. As soon as the device is connected to

the PC operating system will recognize the device. The VCR is seen from the PC as any external

memory that can be browsed with EXPLORER.

Alternatively you can also take out the SD card and connect to the PC via an external SD card

reader.

Switching on the DVR

To turn on and turn off the DVR press the power ON / OFF button on the DVR (13). CAUTION:

Before turning on the DVR the micro SD card must be inserted into its housing and connected to

the camera.

DSE srl - Digital Surveillance Equipment - www.dse.eu

Document: 1N7 DK-PV500LW

DK-PV500LW Portable Digital Video Recorder

The ignition of the device is indicated by the blue LED lit.

Automatic Start recording - The DVR begins recording automatically after power in continuous

mode or motion as programmed. Wait even a minute to complete the boot cycle, at the end will

turn on the red LED that indicates recording in progress. If the red LED does not light it is

necessary to check the connection of the cameras in the presence of the SD card.

REC / STOP - On the top edge of the DVR is the REC / STOP button (12) that allows you to start

and stop recording manually.

Turning WiFi.

This DVR is able to generate its own wireless network to which you can connect with a

smartphone or tablet to control the DVR from your mobile device. By default the WiFi function is

disabled. To activate the WiFi is necessary to turn on the DVR as shown above and then briefly

press the power key (13).

You'll see the orange LED (3) flashes. It means that the DVR is generating a wifi network, acting

as an access point, and waits for the connection of any device.

Once turned on the WiFi, you can download the application and connect to your DVR.

Install the app PV CAM VIEWER.

To control the DVR from mobile app download PV CAM VIEWER from Google Play or Apple

Store. E 'available for free for Android and iOS device. Once installed you will find the icon on

your phone.

ID and CODE of your DVR

Each DVR is marked with a unique ID and a password to access that you find

separating it from the device. Take note of these data that will serve you later in the use of the

app.

WiFi Connection to DVR

In order to use the app PV CAM VIEWER you must first connect your mobile device (phone or

tablet) to the wifi network DVR.

Open the wireless settings of your phone and you will find wifi generated by DVR Network (As P

...), ready to accept your entry.

Connect as with any wifi network. The password to access the factory is:

WIFI PASSWORD:

88888888

Your phone may be noted that with this connection, the Internet is not available. And

The

'normal, accept and go.

Page: 2

under the battery,