DT Research SA1360 Manual de funcionamiento básico - Página 2
Navegue en línea o descargue pdf Manual de funcionamiento básico para Escritorio DT Research SA1360. DT Research SA1360 2 páginas. Digital signage appliance embedded controller/ system
Imprimir páginaSA1360/ DT136
Precautions
•
Always exercise care when operating and handling the SA1360/ DT136.
•
Never disassemble any portion of the enclosure. It will void any product warranty on the SA1360/
DT136.
•
Do not use any AC/DC adapter other than the one provided with the device or acquired from the
manufacturer or its partners.
•
In the unlikely event that smoke, abnormal noise, or strange odor is present, immediately power down
the SA1360/ DT136 and disconnect all power sources.
•
Please report the problem to your device provider immediately.
The SA1360/ DT136
Front View
A
B
C
D
E
F
HDMI port
DC-in
A
D
B
DVI port
E
VGA port
C
USB 2.0 ports
F
Ethernet ports
Powering ON and OFF
The Power Button is located in the front of the SA1360/ DT136. The Power Button may be configured
to function differently depending on the power options of the operating system. In general, to turn the
SA1360/ DT136 on, push and release the Power Button on the front bezel. The power LED will be lit (blue)
and the corresponding interface will be displayed on the display monitor.
To turn off the device, again depending on software operating system, push and release the Power Button
or use a software shutdown interface. In the event of system lockup, the Power Button may be used to
perform a reset on the device. To do that, push and hold the Power Button for at least 4 seconds. The
system will shut down and all unsaved work may be lost. Pushing on the Power Button again will restart
the device.
2
ENGLISH
Rear View
I
J
G
H
K
L
G
J
RS232 COM ports
Power button
H
K
PS/2 ports
Parallel port
I
L
Audio jacks
Omnikey smart card
reader
(optional)
(DT136 only)
Device Ports
The SA1360/ DT136 features an optimal set of I/O ports while preserving the compact size of the system.
The video-out connectors, network (10/100/1000 BaseT Ethernet), COM ports, PS/2 ports, one parallel
port and power ports are supplemented by a set of four USB 2.0 and two audio ports. Through its
USB ports, the SA1360/ DT136 supports a wide range of USB-based peripherals. These peripherals are
applicable in providing the means for software installation, application storage, data storage, and system
software recovery and updates.
Memory and Storage
The SA1360/ DT136 may be available in storage configurations ranging from 32GB, 64GB or 128GB Flash.
Depending on base software configuration, the user may use the internal memory of the DT136 for user's
installed software and storage. The user may also supplement storage space with USB-based peripherals
such as flash disks. RAM capacity is from 4GB to 8GB.
Server Installation
Please refer to the corresponding User Guides for software installation instructions.
Appliance Registration
After turning on the SA1360 for the first time, a screen prompt is
displayed for registering the player. If the screen prompt is not shown,
please follow the instructions below:
1.
Press and hold "Control + Shift + Space" to exit the WCM Player
software.
2.
Navigate to Start | Programs | DT Research | WCM Player
3.
Select Register Player Again. The Player Registration screen should
appear. Fill in all fields to register. The required information is
marked.
4.
Click OK to register and connect to the WebDT Signage Appliance
Publish Server.
SA1360 Options
The SA1360 Signage Appliance is designed to work with a range of custom and off-the-shelf options to
enhance its applicability for various deployments.
* Internal PCI Express wireless LAN (WLAN) adapters with dipole antenna
DT136 Options
The DT136 is designed to work with a range of custom and off-the-shelf options to enhance its applicability
for various deployments.
•
Built-in wireless LAN, with external antenna
•
Omnikey smart card reader
3
ENGLISH