Atwood SACO-2 Manual de información del propietario - Página 2

Navegue en línea o descargue pdf Manual de información del propietario para Alarma de monóxido de carbono Atwood SACO-2. Atwood SACO-2 2 páginas. Atwood mobile products owner's information manual carbon monoxide detector saco-2

Imprimir página

• The detector indicates the presence of CO by a reading on the LCD

and by sounding a beeper.

• Large LCD displays CO levels between 0 and 999 PPM.

• Beeper sounds 3 times continuously between 30-400 PPM.

• Above 400 PPM, the beeper sounds 5 times continuously.

• Bright back-light allows easy screen viewing under dim lighting con-

ditions.

• Battery life indicator (fuel gauge).

• Automatic power off after 10 minutes.

• Max mode stores and displays the maximum CO level taken during

sample time.

• CO level beeper can be silenced if desired.

• Sensor malfunction checking.

• 9V battery is easy to replace.

1 CO Sensor

2 LSR (light sensitive resistor)

3 LCD (liquefied crystal display)

4 "MAX" reading button

5 "ON/OFF" power button

6 Concentration of CO reading

7 Sampling display or

ERR - end of useful life

8 Max reading mode icon

BATTERY INSTALLATION AND SELF TEST

1. Open the battery door and install the battery

2. Close the battery door.

3. Turn the detector on by pressing the ON/OFF button

4. The detector beeps twice, then performs a self-test. The dis-

play shows all the icons then shuts them off and counts down

from 9 to 0.

5. Normal display will show the battery life indicator and the

PPM display amount. A small solid dot will flash every 3 sec-

onds showing that the unit is working correctly.

6. The unit will then be ready to automatically detect CO con-

centration levels.

SELF TESTING

1. The detector will self-test each time the ON button is pushed.

2. If the battery power is below the level required to power the

detector, the detector will emit a beep and show Lb (indicating

low battery) in the display window and the battery icon will show

level or empty bars. This indicates you must replace the battery.

3. If the detector shows Err and the sensor malfunction icon

shows on the display, the sensor has been damaged or failed.

See warranty for action.

ESTABLISHING A BASELINE

1. Before testing for CO, the detector establishes a baseline

against which the detector compares other environments.

2. Do this by turning on the detector in a clean environment.

3. If the detector reads between 0-6 PPM, it does not establish

a new baseline, but starts taking CO measurement.

FEATURES

OPERATIONS

9 Battery life indicator

10 Sensor malfunction icon

11 Mute beeper icon

12 Beeper

13 Battery connector

14 Battery door

15 Battery 9 volt

FIG

MAXIMUM READING

1. To obtain the maximum reading of CO press the MAX button,

the beeper emits one chirp and the MAX icon will display in

the top left corner of the display.

2. The reading on the LCD refers to the maximum value, which

has been detected by the unit.

3. After a few seconds the display will restore back to normal

test mode and the MAX icon will disappear.

MUTING THE BEEPER

1. To mute the beeper, press the MAX button for more than 2

seconds.

2. The mute beeper icon will appear on the bottom left corner of

the LCD.

3. To re-enable the beeper, press the ON/OFF button, this will

turn the detector off and then back on.

AUTO BACK LIGHT

1. If the ambient light is too low (making the LCD difficult to

read), the LCD back light will automatically turn on.

2. The back light will automatically turn off when there is suffi-

cient light.

AUTOMATIC POWER OFF

1. The detector will automatically turns off after 10 minutes of

none-use.

MEASUREMENT RANGE

: ....................1 PPM

SENSITIVITY

: ......................62% full scale

ACCURACY

: ......................60 seconds @ 90% of final value

RESPONSE

TYPICAL SENSOR LIFE

: ........................9 volt

BATTERY

OPERATING TEMPERATURE

OPERATING HUMIDITY

: ..........................5.2 ounce (150 grams)

WEIGHT

: ....................7 x 2.3 x 2" (180 x 60 x 50 mm) approximately

DIMENSIONS

: ..............<30 PPM = 1 min <999 PPM = >2 min.

RECOVERY TIME

1. The detector requires no calibration or servicing.

2. If detector does not operate check battery conditions and

replace with new battery.

3. If detector still does not operate properly destroy and discard

FIG

the CO monitor.

Transportation by sea, land and air is acceptable for this prod-

uct. During shipping, care should be taken to avoid collision,

rain, snow and mixture of corrosive materials. During the loading

and unloading, strictly prohibit the throwing of product. The

product should be stored in a clean room with the ambient tem-

perature of 23

more than 95% and free from any corrosive vapors and harmful

impurities in the air.

Atwood Mobile Products

to be free from defects in material and workmanship for a period

of 90 days from the date of purchase by the Original Purchaser.

"Original Purchaser" is that person who purchases a new car-

bon monoxide monitor for his own use. If there is any defect in

the manufacturing of, or failure of any such monitor which is

reported within the aforesaid ninty day period, Atwood will, with-

in a reasonable time and without charge, make repairs and

replacements as needed. In no case shall liability under any

other remedy prescribed by law exceed the purchase price. Your

monitor is not a substitute for Property, Disability, Life or other

insurance coverage: appropriate insurance coverage is the

owner's responsibility.

SPECIFICATIONS

: ......0-999 PPM, (above 999 PPM display OL)

(at temperature: 70˚F-78˚F (21˚C-64˚C)

:........more than 10 years

: ..23

F - 104

F (-5

C - 40

: ........0-97% relative humidity (non-condensing)

MAINTENANCE

STORAGE AND SHIPPING

F - 104

F (-5

C - 40

C). Relative humidity of no

WARRANTY

warrants its carbon monoxide monitor