Auber JSL-71A Manual de instrucciones

Navegue en línea o descargue pdf Manual de instrucciones para Timer Auber JSL-71A. Auber JSL-71A 6 páginas. Auber easy timer with dual settings

Imprimir página

AUBER INSTRUMENTS

Instruction Manual

Overview

This JSL-71 timer can count from 0.01 second to 9999 minutes. Operating

function modes include single delay, double delay, and cycle delay. It can

count-down or count-up. The timer can be activated automatically when

powering up, by front key pad, or via remote switch. Two different time delay

settings can be programmed. User can switch the setting with a single key

press. Lock function can be activated to prevent any accidental change.

2. Specification

Timer range: 0.01 second to 9999 minutes

Timer mode: single delay, double delay, cycle delay

Timer trigger: power on, front key pad, or remote switch

Timer accuracy: <1s/day.

Power supply: 90-260V AC or DC.

Power consumption: <2W

Relay output:7A@240VAC,10@120VAC and 24VDC

Relay life: 100,000 times.

Operating temperature: 0-60 ° C.

Humidity: 0-95%RH

Panel cutout: 44.5x44.5mm

Outer dimension: 48x48x85 mm.

3. Front Panel

Figure1. Front panel

1. RUN indicator: (the red dot at the lower right corner).Turns on when timer

starts running. Turns off when timer stops.

2. Time unit indicator: turns on when time units are M:S or H:M. Turns off when

time unit is M or S.

3. Time range indicator: turns on when the time base is H:M (Hours: Minutes)

or M(Minutes). Turns off when the time base is M:S (Minutes : Seconds) or

S(Seconds).

4. Timer indicators: T1 for first delay time, T2 for second delay time.

5. OUT indicator: Turns on when relay is on. Turns off when relay is off.

6. SET key. When timer is not running, press it will switch between first delay

time setting (T1) and second delay time setting (T2); press and hold it for 3

second will enter the programming mode.

2015.04

JSL-71A Easy Timer with Dual Settings

Version 1.2 (Apr, 2015)

7. Down key / STP key: Lower the time setting value or stop the timer (for

special stop function please see note2 on page 5/5 for details). In the

programming mode, press it will go to the next programming value.

8. Up key / PAU key: When timer is not running, press it will increase the time

setting value. When timer is running, press and hold it will pause the timer. The

timer will continue running after this key is released. In the programming mode,

press it will go to the previous programming value.

9. RST key: Reset key. When timer is running, press it will restart the timer. If

"RUN" parameter is set to RST, press it will start the timer after powered up.

10. LED digital display. During normal operation as a timer, the top displays the

actual time; the bottom displays the set value. In programming mode, the top

displays setting parameters; the bottom displays programming value.

4. Terminal Assignment

Details:

Power for the timer needs to be connected to between terminal 9 and 10. The

voltage should be in the 90 to 260V range.

Terminal 6, 7 and 8 are for relay output. Terminal 6 is Normally-closed (NC)

contact. Terminal 8 is Normally-open (NO) contact. Terminal 7 is common

contact of the terminal 6 and 8. When the relay is energized (or when the OUT

LED is on), terminal 8 connects to terminal 7, and terminal 7 disconnects

terminal 6; When the relay is NOT energized (or when the OUT LED is off),

terminal 6 connects to terminal 7, and terminal 7 disconnects terminal 8. The

relay is a "dry switch" that does not provide power by itself. Please see the

wiring example below.

Terminal 5 is the reset terminal that has the same function as the RST key in

the front panel. Terminal 4 is the pause/mute terminal that function the same

as the "^/PAU" key in the front panel. Terminal 3 is the stop terminal that

function the same as the "V/STP" key in the front panel. Terminal 1 and 2 are

the common contacts of the terminal 3/4/5. There are two ways to operate

terminal 3, 4 and 5.

1) Connecting a normally open (NO) momentary push button switch between

the terminal (3, 4 or 5) to the COM (1 or 2). Please note, the function starts

when you release (or open) the button of the switch, not when you press down

the switch.

WWW.AUBERINS.COM

Figure 2. Terminal assignment.

P1/4