Auber Instruments EZboil DSPR310D Manual de instrucciones - Página 2

Navegue en línea o descargue pdf Manual de instrucciones para Controlador Auber Instruments EZboil DSPR310D. Auber Instruments EZboil DSPR310D 14 páginas. For step mashing and boiling process automation
También para Auber Instruments EZboil DSPR310D: Manual rápido (2 páginas)

Imprimir página

AUBER INSTRUMENTS

described later, we suggest you connect the hot wire to terminal 10 and neutral

to 9.

3.3 SSR output connection

The SSR control output of the DSPR310D provides a 12 VDC signal that can

control up to 5 SSRs in parallel. Connect terminal 7 to the positive pole of the

SSR (terminal 3 on Auber's SSRs). Connect terminal 6 to the negative pole of

the SSR (terminal 4 on Auber's SSRs). Please make sure the SSR is installed

on the heat sink with proper current rating.

4. Display Status

Power on

Display mode 1

100

Press down and

Hold for 5s

Exit

Knob

goto

Mash

Parameter settings

Figure 3. Display modes of DSPR310D.

Display mode 1 (Normal operating mode): 1) When MASH indicator is ON,

the controller is in step mashing mode. The top display will show reading

temperature, and it may also flash the remaining time for the current step

alternately (see section 5.2.1). The bottom display will flash set temperature in

this step and current step number (e.g. P-1 for step 1) alternately. 2) When

MASH indicator is OFF, the controller is in boiling mode. The top display will

show reading temperature, and it may also flash the total remaining time of timer

events alternately (see section 5.3.1). The bottom display will flash current output

power percentage (e.g. P50 for 50% power output) and current step number

alternately.

Display mode 2 (Step program reset & Operation mode selection): This

display mode allows you to reset the timer (mashing and boiling modes), or to

switch between the mashing and boiling operation mode.

A short press of the knob will enter this display mode.

1) The display will show "rSt" on top and "n" at the bottom. This is the exit menu.

If you enter this mode by accident, you can press the knob again to exit this

display mode without changing anything.

2) Rotate the dial clockwise for one click will change the bottom display to "y".

This option is to stop the program steps/timer events. Bottom display will flash

"stop". It functions the same if you press and hold the Key B for 5 seconds.

3) Rotate the knob with two clicks, the top display will change to "Mode" and

bottom will show "Mash", which is for step mash mode. Rotate the knob again,

the bottom display will change to "Boil", which is for boil mode. These two menus

are for setting the controller to either step mashing control or boiling control mode.

Press the knob will set the controller to the operation mode displayed. Please

check section 5.1 for details.

Display mode 3 (Parameter settings): Press down and hold the knob for 5

seconds to enter the display mode 3. Please check section 6 for details.

2018.08

Display mode 2

rst

Press

Knob

Exit

Timer reset /

mode selection

Display mode 3

Press

Next parameter

Knob

5. Operation

5.1 Operation mode selection

This controller offers two operation modes, step mashing and boiling. When the

step mashing mode is selected, the controller functions as a temperature

controller with steps. It automatically adjusts the power output to hold the

temperature at set point in that step. When boiling control mode is selected, the

controller functions as a power regulator. It allows the user to manually adjusting

the power to control the strength of the boil. Figure 4 shows how to select and

switch between these two modes.

Knob Press

Knob

mode

mash

Knob

mode

boil

Figure 4. Flow chart for timer reset & operation mode selection.

Press the knob once. The display will show "rSt". Rotate the knob with two clicks,

the top display will change to "Mode" and bottom will show "Mash*". Press the

knob will set the controller to mashing mode. When mashing mode is selected,

the yellow indicator on the top left corner of the panel will lit. This indicator will

be off if the boiling mode is selected.

Note 1: due to the limitation of 7 segment LED display, the letter "M" is displayed as "m".

Note 2: if you mistakenly enter this layer of setting, you need to dial the knob to show:

Then press the knob again to exit. Nothing will be changed.

5.2 Step Mashing Operation

5.2.1 Introduction

When first powered up, make sure the controller is in the mashing mode: The

yellow colored mashing mode indicator on the upper left corner should be on,

and the bottom display has no "P" on the left. If not, please change the control

mode to mashing mode as discussed in section 5.1 above. If you were using the

controller in the step mashing mode when powered off last time, the controller

will start in the step mashing mode.

After controller is powered up, the top LED displays the current temperature

reading from the sensor. If temperature sensor is not connected, it will show

"orAL". When the step mashing timer is triggered and counting down, the top

display will start to display the current temperature and the remaining time for

the current step alternately. The bottom LED displays your current set

temperature, and it may also flash current step status alternately, including "run",

"hold" and "stop".

WWW.AUBERINS.COM

100

Press

rst

Exit

Knob

Rotate

Press

rst

Timer Reset

Knob

Rotate

Press

Step Mash

Mode

Knob

Rotate

Press

Boil Mode

Knob

P2/14