Conairphone CID200 Manual del usuario - Página 3
Navegue en línea o descargue pdf Manual del usuario para Teléfono inalámbrico Conairphone CID200. Conairphone CID200 7 páginas. Caller id speakerphone with 10 memory dialing
CONGRATULATIONS!
You have purchased a CID200, 10-Memory Caller ID Telephone
manufactured to the highest standards of Conairphone
installing and operating, be sure to read this manual.
LOCATION OF CONTROLS
1
2
3
4
5
6
7
1. Hook Switch
12. Erase Button
2. Receiver
13. Ringer Hi/Lo/Off Switch
3. Call Back Button
14. Review
4. Pause Button
15. Tone/Pulse Switch
5. Receiver Volume Control
16. Contrast Button
6. Priority Button
17. Volume Control
7. Transmitter
18. Keypad
8. Memory Button
19. Redial Button
9. Store Button
20. Flash Button
10. LCD Display
21. Speakerphone LED
11. New Call LED
22. Speaker Button
4
GENERAL INFORMATION
UNPACKING
TM
. Before
This package contains:
• CID200 Caller ID Speakerphone
• Owner's Manual
• One (1) Fully Modular Coil cord
• One (1) Quick Installation Guide
• One (1) Important Notice
• One (1) Safety Instructions for Batteries
• Two (2) Additional Memory Index Labels
10
• Warranty Card (Part of the Owner's Manual)
11
12
If anything is missing or damaged, contact the place of purchase.
Keep the packaging to transport telephone.
13
14
15
For your reference, keep a record of the date purchased.
16
Please save the sales receipt for the warranty reference.
17
18
Date of Purchase ___________________________
19
20
INSTALLATION INSTRUCTIONS
21
22
Follow these precautions:
a. Never install telephone wiring during a lightning storm.
9
8
b. Never install telephone jacks in wet locations unless the jack
is specifically designed for wet locations.
c. Never touch uninsulated telephone wires or terminals unless
the incoming telephone line has been disconnected at the
network interface.
d. Use caution when installing or modifying telephone lines.
/
Button
TO INSTALL BATTERIES
Batteries are required for the Caller ID functions and Telephone
operations of the unit.
1. Remove the screw and open the battery door by pulling back
the latch.
5
2. Insert four (4) AA alkaline batteries (not included).
3. Snap the battery door back into place and replace the screw.
USING THE PHONE ON A DESK
1. Connect the coiled cord to the jacks in the handset and the
left side of the base.
2. Follow the "Setting up your CID200" instructions to set up
your telephone.
3. After the Caller ID setup has been completed, connect the
telephone line cord into the wall outlet.
HANGING THE PHONE ON THE WALL
The CID200 can be mounted on a standard wall phone plate
or two screws, installed 3
1
/
" vertically apart in the wall. Leave
4
3
/
" of each screw exposed for mounting the unit.
16
1. • On a wall phone plate
Coil the telephone line cord inside the wall mount pedestal
and slip the end of the cord through the rectangular
opening.
• On a Wall
Align the telephone line cord with the right slot on the top
and bottom of the wall mount pedestal.
2. To attach the wall mount pedestal, insert the tabs into the
slots in the base, making sure the telephone cords in the top
and bottom slots.
3. Attach the assembly to wall by inserting the two studs of the
wall plate (or the two screws) into the slots on the back of the
wall mount pedestal. Pull down gently for a snug fit.
4. Plug the coil cord into the handset and base jacks.
5. Follow the "Setting up your CID200" instructions to set up
your telephone.
6. After the Caller ID setup has been completed, connect the
telephone line cord into the wall outlet.
6