ADDER ADDERLink INFINITY 3000 Inicio rápido

Navegue en línea o descargue pdf Inicio rápido para Receptor ADDER ADDERLink INFINITY 3000. ADDER ADDERLink INFINITY 3000 2 páginas.
También para ADDER ADDERLink INFINITY 3000: Manual de inicio rápido (2 páginas)

Imprimir página

ADDER ADDERLink INFINITY 3000 Inicio rápido

Initial configuration

ALIF3000 units depend upon ADDERLink INFINITY Manager (AIM) for almost all of their

configuration. As a new ALIF3000 unit is added to a network it must be in its factory default mode so

that AIM can engage with it and begin managing its resources. If an ALIF3000 is not in factory default

mode, please see the center pages.

To connect and configure an ALIF3000

1 Connect the ALIF3000 to an AIM-controlled network using either of the SFP ports via a suitable

CATx or fiber SFP module.

2 Connect the necessary peripheral devices to the ALIF3000 and apply power to it via the supplied

power adapter.

3 The OLED screen on the front panel will provide status information:

ALIF 3000

–––––––––––––––

Searching...

Connecting...

You should see the message progress from Searching... to Connected.

4 Log into AIM as an administrator and locate the new ALIF3000R entry within the Receivers section.

5 Click the

icon on the ALIF3000R entry to configure the device. Please see the AIM user guide for

further details.

www.adder.com/en/kvm-solutions/adderlink-infinity-3000

www.adder.com

Part No. MAN-QS-ALIF3000-ADDER_V1.1

ALIF 3000

–––––––––––––––

Connected

Full user details and setup instructions can be found at:

ADDERLink

Welcome

This quick start guide covers some of the key points of the

ADDERLink™ INFINITY 3000 (ALIF3000) unit, which has

been created to address the growing requirement to connect

users to both physical and virtual machines. Using standard

VDI (Virtual Desktop Infrastructure) protocols - which are

built-in; the ALIF3000 delivers seamless access to legacy KVM

systems as well as Virtual Machine (VM) sources, from the

same common console.

Dual DisplayPort

video outlets provide support for a

single 2560x1600 display or two at a maximum 1920x1200

resolution (60Hz refresh).

Gigabit connections

The ALIF3000 receiver has two SFP ports located on its rear

panel, which can accommodate a range of fiber or copper

networking modules, as suits your installation. Each port

can be connected to a separate gigabit fiber (or copper)

network to permit access to a wider range of systems. A

third network port (RJ45) is also provided to allow separate

access, where necessary, to a corporate network to gain the

VM hosting configuration data. All three connections are

securely isolated within the ALIF3000 to prevent any cross

contamination between networks.

Important

ALIF3000 can ONLY be connected as part of an ADDERLink INFINITY system that is administered by

an ADDERLink INFINITY Manager. See rear page for Initial configuration details.

It is important that each ALIF3000 is set to its factory default settings, otherwise it will not be

discovered by the AIM server. If the ALIF3000 has previously been used in a different system, you

merely need to perform a manual factory reset on each unit. Please see the center pages.

Minimum versions

In a mixed ALIF installation, ensure that the various

components have the following software versions:

• AIM server:

v4.11

• ALIF100T-DVI:

v4.07

• ALIF100T- VGA: v4.08

• ALIF1xxx:

v4.9

• ALIF2xxx:

v4.9

• ALIF3xxx:

v1.0

• ALIF4xxx:

v3.0

INFINITY 3000

™

Quick Start

ALIF3000

Network

ALIF TX

Legacy KVM

Virtual

system(s)

machines

Full user details and setup

instructions can be found

at www.adder.com/en/

kvm-solutions/adderlink-

infinity-3000

Please read the supplied safety

instruction leaflet before use.

switch