Danfoss VLT FC Series Manual de instrucciones de instalación - Página 2
Navegue en línea o descargue pdf Manual de instrucciones de instalación para Controlador Danfoss VLT FC Series. Danfoss VLT FC Series 6 páginas. Igbt module replacement for d1h–d8h drives
También para Danfoss VLT FC Series: Manual de instalación (12 páginas), Manual de instrucciones de instalación (6 páginas), Manual de instalación (8 páginas), Manual de instrucciones (11 páginas), Manual de instalación (6 páginas)
Imprimir página
Installation Instructions
Installation
NOTICE
®
The VLT
Wireless Communication Panel LCP 103 is hot-
pluggable and can be connected when the drive is powered
on.
1.
Mount the LCP 103 in the LCP input plug on the
drive.
®
2.
Search for MyDrive
Store.
®
Illustration 1.2 MyDrive
Connect Launch Icon
3.
Download and install the MyDrive
NOTICE
Start pairing within the first 10 minutes after the instal-
lation. Failing to do so closes the broadcast or wireless
identification due to security limits with default passwords.
To reconnect, power cycle the drive, or remove and
reconnect the LCP 103.
Connection Procedure
NOTICE
The wireless SSID is the Danfoss serial ID of the drive. For
example, Danfoss_019223G455 is the default wireless SSID
for a drive with the serial number 019223G455. The serial
number is on the product nameplate, but is also visible in
parameter 15-51 Frequency Converter Serial Number.
Wireless SSID
Default password
1.
Open the app and establish the Wi-Fi connection, see
Table 1.1 for descriptions of the white Wi-Fi LED.
2.
When prompted, change the default password due to
security restrictions. The password must be at least 8
and maximum 48 characters.
3.
Re-plug the LCP 103 for the password to change into
effect. Failing to do so allows the LCP 103 to keep
broadcasting.
4.
Disconnect the app, navigate to smart device
settings, and forget the network.
5.
Search for the wireless network and connect with the
new password.
2
®
VLT
Wireless Communication Panel LCP 103
®
VLT
FC Series FC 102, FC 103, FC 202,
FC 301/FC 302, and LD 302
Connect in Google Play or Apple
®
Connect App.
Danfoss_019223G455
Danfoss1933
Danfoss A/S © 08/2018 All rights reserved.
NOTICE
If the password is not changed, it leaves only 10 minutes for
connecting and performing Drive operations. After this, the
wireless connection closes.
Reset password
If the wireless SSID and password are forgotten, access
parameter group 30-9* Wifi LCP via MCT 10 Set-up Software or
LCP 102.
LED Pattern
LED
Pattern
Description
On
Solid
The drive is powered on (normal operation).
green
Flashing
Connection pairing successful.
white
Wi-Fi
Solid
The smart device is connected and communi-
white
cation is OK.
Alarm
Flashing
An alarm has occurred.
red
Warn
Solid
A warning has occurred.
yellow
Flashing
Identification of the drive when initiated through
MS,
orange
a winking command.
NS1,
Flashing
Incompatible drive (LED flashes 3 times and then
1)
NS2
orange
remains on).
Table 1.1 Descriptions, LED Indicators
1) MS=module status, NS1=network status 1, NS2=Network status 2.
Safe Control
The safe control parameter allows the drive to decide the
motor behavior if the smart device, for example a tablet,
communication is lost. If the limits are set to [1] Stop motor,
the motor stops. If the limits are set to [0] Do nothing, the
motor continues to run. This is only applicable when the
motor is in Run state and if the motor has been started from
the app.
The communication happens between the MyDrive
®
App and the VLT
Wireless Communication Panel LCP 103.
Parameter
Parameter 30-97 Wifi Timeout Action
®
Connect
Limits/options
[0] Do nothing
[1] Stop motor
MI38V402