Danfoss VLT AutomationDrive FC 360 Manual de instrucciones
Navegue en línea o descargue pdf Manual de instrucciones para Accionamientos de CC Danfoss VLT AutomationDrive FC 360. Danfoss VLT AutomationDrive FC 360 2 páginas. 90–315 kw, enclosure sizes j8–j9
También para Danfoss VLT AutomationDrive FC 360: Instrucciones de instalación (4 páginas), Instrucciones de instalación (4 páginas), Instrucciones de instalación (2 páginas)
Imprimir página
Operating Guide
VLT® AutomationDrive FC 360
90–315 kW, Enclosure Sizes J8–J9
1 Introduction
This operating guide provides necessary information for quali ed personnel to install and commission the
AC drive. Read and follow the instructions to use the drive safely and professionally.
Do not dispose of equipment containing electrical components together with domestic waste.
Collect it separately in accordance with local and currently valid legislation.
2 Safety
Pay particular attention to the safety instructions and general warnings to avoid the risk of death, serious
injury, and equipment or property damage.
W A R N I N G
HIGH VOLTAGE
AC drives contain high voltage when connected to AC mains input.
UNINTENDED START
The motor may start from control panel, I/O inputs, or eldbus at any time, when the drive is connected to the AC mains.
DISCHARGE TIME
The drive contains DC-link capacitors, which can remain charged even when the drive is not powered. High voltage can be
present even when the warning indicator lights are o .
- Stop the motor, and disconnect AC mains, permanent magnet type motors.
- Wait for the capacitors to discharge fully and measure it before performing any service or repair work.
- The minimum waiting time is 20 minutes.
LEAKAGE CURRENT
Leakage currents of the drive exceed 3.5 mA. Make sure that the minimum size of the ground conductor complies with the
local safety regulations for high touch current equipment.
3 Installation
3.1 Mechanical Dimensions
C
E
G
Front view
Side view
Illustration 1: Mechanical Dimensions, Enclosure Sizes J8–J9
Table 1: Power Ratings, Dimensions, and Weights for Enclosure Sizes J8–J9
Power [kW (hp)]
Height [mm (in)]
Enclosure size
(IP20)
3x380–480 V
A
A
a
(1)
J8
110–160 (150–250)
889 (35.0)
909 (35.8)
844 (33.2)
J9
200–315 (300–450)
1096 (43.1)
1122 (44.2)
1051 (41.4)
Depth [mm (in)]
Mounting hole [mm (in)]
Center of gravity [mm (in)]
Enclosure size
(IP20)
C
D
E
J8
375 (14.8)
11 (0.4)
128 (5.0)
J9
375 (14.8)
11 (0.4)
176 (6.9)
Note: (1) Including decoupling plate.
3.2 Removing the Front Cover
*M0040301*
Procedure:
Step 1: Loosen and remove the 2 screws on the front cover.
130R1294
Step 2: Disconnect the front cover from the hooks.
Screws
3.3 Connecting to Mains, Motor, Control Terminals, and Relays
B
b
D
Control
terminals
Relays
D
3.4 Control Terminals
b1
Back view
Width [mm (in)]
50 53 54 42 45 55
B
b
b1
250 (9.8)
180 (7.1)
200 (7.9)
350 (13.8)
280 (11.0)
271 (10.7)
Maximum
weight
[kg (lb)]
F
G
12 18 19 27 29 31 32 33 20
495 (19.5)
148 (5.8)
98 (216)
611 (24.1)
148 (5.8)
164 (362)
Step 2
Step 1
Illustration 2: Removing the Front Cover
Illustration 3: Connecting to Mains, Motor, Control Terminals, and Relays
RS485 termination switch
(ON=RS485 terminated, OFF=Open)
61 68 69
RELAY 1
RELAY 2
01
02
03
04
Illustration 4: Control Terminals
4 Speci cations
Table 2: Electrical Data for Normal Overload, Mains Supply 3x380–480 V AC
Drive
Enclosure size
Normal overload=110% current during 60 s
Typical shaft output at 400 V [kW]
Typical shaft output at 460 V [hp]
Output current (3-phase)
Continuous (at 400 V) [A]
Intermittent (60 s overload) (at 400 V) [A]
Hooks
Continuous (at 460 V) [A]
Intermittent (60 s overload) (at 460 V) [A]
Continuous kVA (at 400 V) [kVA]
Continuous kVA (at 460 V) [kVA]
Maximum input current
Continuous (at 400 V) [A]
Continuous (at 460 V) [A]
Maximum number and size of cables per phase
Mains and motor [mm (AWG)]
Maximum external mains fuses [A]
Estimated power loss at 400 V [W]
Estimated power loss at 460 V [W]
E ciency [%]
Output frequency [Hz]
Heat sink overtemperature trip [°C (°F)]
Control card overtemperature trip [°C (°F)]
Table 3: Electrical Data for High Overload, Mains Supply 3x380–480 V AC
Drive
Enclosure size
High overload=150% current during 60 s
Typical shaft output at 400 V [kW]
Motor
Typical shaft output at 460 V [hp]
Output current (3-phase)
Continuous (at 400 V) [A]
Mains
Intermittent (60 s overload) (at 400 V) [A]
Continuous (at 460 V) [A]
Ground
Intermittent (60 s overload) (at 460 V) [A]
Continuous kVA (at 400 V) [kVA]
Continuous kVA (at 460 V) [kVA]
Maximum input current
Continuous (at 400 V) [A]
Continuous (at 460 V) [A]
Maximum number and size of cables per phase
Mains and motor [mm (AWG)]
Maximum external mains fuses [A]
Estimated power loss at 400 V [W]
Estimated power loss at 460 V [W]
E ciency [%]
Output frequency [Hz]
Heat sink overtemperature trip [°C (°F)]
Control card overtemperature trip [°C (°F)]
5 Ambient Conditions
J8–J9 enclosure size
Vibration test (standard)
Relative humidty
Aggressive environment (IEC 60068-2-43) H
Aggressive gases (IEC 60721-3-3)
05 06
Test method according to IEC 60068-2-43
Danfoss A/S © 2023.06
Q110
Q132
Q160
Q200
Q250
Q315
J8
J8
J8
J9
J9
J9
110
132
160
200
250
315
150
200
250
300
350
450
212
260
315
395
480
588
233
286
347
435
528
647
190
240
302
361
443
535
209
264
332
397
487
589
147
180
218
274
333
407
151
191
241
288
353
426
204
251
304
381
463
567
183
231
291
348
427
516
2x95 (2x3/0)
2x185 (2x350 mcm)
315
350
400
550
630
800
2559
2954
3770
4116
5137
6674
2261
2724
3628
3569
4566
5714
98
0–590
110 (230)
75 (167)
80 (176)
H90K
H110
H132
H160
H200
H250
J8
J8
J8
J9
J9
J9
90
110
132
160
200
250
125
150
200
250
300
350
177
212
260
315
395
480
266
318
390
473
593
720
160
190
240
302
361
443
240
285
360
453
542
665
123
147
180
218
274
333
127
151
191
241
288
353
171
204
251
304
381
463
154
183
231
291
348
427
2x95 (2x3/0)
2x185 (2x350 mcm)
315
350
400
550
630
800
2031
2289
2923
3093
4039
5004
1828
2051
2089
2872
3575
4458
98
0–590
110 (230)
75 (167)
80 (176)
IP20/Chassis
0.7 g
5%–95% (IEC 721-3-3; Class 3K3 (non-condensing) during operation)
S test
Class Kd
2
Class 3C3
H
S (10 days)
2
AQ435824155085en-000101 / 130R1294 | 1