Free The Tone MOTION LOOP Manual de inicio rápido
Navegue en línea o descargue pdf Manual de inicio rápido para Pedal de música Free The Tone MOTION LOOP. Free The Tone MOTION LOOP 2 páginas. Pitch shiftable short looper
Imprimir página
MOTION LOOP
PITCH SHIFTABLE SHORT LOOPER
QUICK START GUIDE
Controls and Indicators
Front Panel
RATE Knob / KNOB-L
E.LEVEL Knob / KNOB-C
Adjusts the sampling duration for loop
Adjusts the balance between the
operation.
original sound and effect level.
Turning the knob clockwise increases
the effect level.
SAVE Switch
Press this switch to save the setting.
HOME Switch
Press this switch to change the contents
shown in the display. Holding this switch
down for about 2 seconds puts the unit
in Global Function Setting mode.
Display
Shows preset names or parameters of
various functions.
ON/OFF Footswitch
Press this footswitch to turn on/off the
loop effect. When it is turned on, the LED
at the right side of the footswitch
illuminates. If this footswitch is set to
Unlatch operation, this LED illuminates
as long as the footswitch is held pressed.
Main Specifications / Ratings
• Number of presets: 128 user presets, 35 factory presets
• Input impedance: 1 M
• Output load impedance: min. 10 k
• Max. input level: +10 dBm
• Terminals: 1 x 1/4" standard TRS phone jack (IN(TRS)), 3 x 1/4"
standard TS phone jack (OUT/L, OUT/R, EXP/CV/FS), 9 VDC input
jack (for AC adapter), 3.5-mm stereo mini jack (MIDI IN)
• Power supply: Optional AC/9VDC adapter (FA-0905D-JA/UK/EU,
FA-0905H-JA), 006P (9V) 6F22 battery (alkaline type)
• Current consumption: approx. 185 mA
• Dimensions: 66 (W) x 125 (D) x 54 (H) mm (incl. protrusions
such as jacks)
• Weight: approx. 335 g
• Accessories: Warranty card, Quick start guide, Safety
instructions, Rubber feet
NOTE: Specification and external appearance may change without
notice.
Please download detailed instruction manuals from the
SUPPORT page on our website.
www.freethetone.com/en/support/download/
FILTER Knob / KNOB-R
Adjusts the filter operation.
◀ / ▶ Cursor Key
Used to switch menu or setup screens.
The ◀ cursor key operates as the
previous page switch and the ▶
cursor key operates as the next page
switch.
PARAMETER Encoder
Used to adjust parameters of each
function.
PRESET LEDs
When a BPM (tempo) has been set,
both of the LEDs flash in that tempo.
PRESET Footswitch
Press this footswitch to switch
between Presets 1 and 2. It is also
used as a confirmation switch when a
preset is recalled using the
PARAMETER encoder. If this footswitch
is set for retriggering in any preset, it
operates as the footswitch for
retriggering when the effect has been
enabled.
Top Panel
IN(TRS) Terminal
Used to connect a guitar/bass or another
musical instrument or effects unit. For a
monaural input use a cable terminated
with monaural phone plugs. For a stereo
input use a cable with TRS phone plugs.
NOTE
In addition to the AC adapter, the MOTION LOOP can be powered by a 006P (9 V) alkaline battery.
Battery life for continuous use is about 2 hours (this depends on the type and usage condition of the battery). Please note that a manganese dry cell cannot be used due to
its short life. When the battery voltage becomes too low, the display shows "LOW BATTERY". Exchange the battery or use the AC adapter.
When replacing batteries, remove the bottom plate after loosening the four screws on it and replace the battery with a new one.
Side Panel
OUT/R Terminal
Used to connect to an amplifier,
mixer, etc.
Display Contents
By pressing the HOME switch the display alternately shows the HOME
screen and Function Assignment screen.
1. HOME screen: Indicates a preset number and preset name.
Preset Number
OO1
UFO
Preset Name
2. Function Assignment screen: Indicates the function assigned to a
knob or encoder.
When this screen is displayed, each knob or PARAMETER encoder is
used to change the parameter of the assigned function.
KNOB-L
KNOB-C
KNOB-R
FEED
PIT
LOOP
BACK
SPD
LVL
LP-R-MD
OO1
NONE
Preset Number
PARAMETER Encoder
OUT/L Terminal
Used to connect to an amplifier or mixer, etc.
When this unit is battery powered, inserting
a plug in this jack turns on the power.
DC9V Terminal
Used to connect the optional AC/DC adapter
FA-0905D-JA/UK/EU or FA-0905H-JA. An
adapter with regulated 9-VDC output,
center minus polarity, and power supply
capability of higher than 200 mA. Accepts a
standard 5.5-mm x ø2.1-mm plug.
MIDI IN Terminal
Used to receive MIDI signals. The
optional CM-3510-TRS MIDI cable is
applicable.
EXP/CV/FS Terminal
Used to connect an expression pedal
or external footswitch (momentary
type). This terminal accepts CV
(control voltage).
Holding the HOME switch down for about 2 seconds brings up the
SETUP screen.
3. SETUP screen: Displayed when the MOTION LOOP's Global
functions such as MIDI channel setting are set.
Shows that there is a next page
SETUP
MIDI CH
Global
Function
CH1
Parameter
By pressing the ▶ cursor key while the HOME or Function
Assignment screen is shown, the MENU screen for setting up various
functions.
4. MENU screen: Displayed when changing effects unit's parameter
in each preset and changing functions for each control.
MENU
[
]
PITCH
SETTING