Daniela DDW300 Manual del usuario - Página 4

Navegue en línea o descargue pdf Manual del usuario para Lavavajillas Daniela DDW300. Daniela DDW300 6 páginas. Domestic dishwasher

Imprimir página

Starting the Appliance

Starting a wash cycle

After having completed all of the installation steps in the preced-

ing paragraphs, turn on the water to the unit, partially open the

door of the dishwasher, and press the ON-OFF button "A" lo-

cated on the control panel. The "B" indicator light will come on.

At this point, the appliance is on and ready to be programmed.

Setting and Starting a wash Cycle

Choose the desired cycle by pressing the cycle selection button

"G". Each time it is pressed, the cycle indicator lights "F" will

change to indicate the cycle selected.

Choose the wash cycle you feel is most appropriate for the type

of dishes that need washing (consult the wash cycle table con-

tained in this manual, especially when first using the appliance).

Close the door and after a few seconds, The wash cycle will begin.

Read the paragraph entitled, "Cancelling or changing a cycle while

underway. "The end of the cycle will be signalled by six beeps,

and the indicator light "F" will extinguish.

Cancelling or changing a cycle while underway...

Premise: A cycle that is underway can only be changed if it has

only been running for a short time.

Otherwise, the detergent may have already been used, and the

appliance may have already drained the wash water. If this is the

case, the detergent dispenser must be refilled (see the paragraph

entitled, "Loading the Detergent").

To change the cycle currently underway, open the door, press

the "G" programming button and hold it in for about 5 seconds.

Once the cycle has been cancelled, the dishwasher will emit a

short acoustic sound and the relative indicator light will turn off.

To set a new wash cycle, follow the instructions contained in the

paragraph entitled, "Setting and Starting a Wash Cycle."

At the end of the wash cycle...

Six beeps will indicate that the wash cycle has finished and the

cycle indicator light "F" will begin to extinguish. Open the door,

turn off the appliance using the ON/OFF switch and turn off the

water supply to the unit. Wait a few minutes before removing the

dishes so as to avoid handling them while still hot (when they

are more susceptible to breakage) and to get better drying results.

Setting The Start Delay Time

Open the door of the dishwasher partially. Press button "J" (see,

Close-up View" Control Panel") to delay the starting time for a

wash cycle.

.1st press, "2h" indicator comes on, the cycle will start in 2 hours.

.2nd press, "4h" light indicator comes on, the cycle will start in 4

hours.

.3rd press, "6h" light indicator comes on, the cycle will start in 6

hours.

.4th press, "2h" and "6h" light indicators come on, the cycle will

start in 8 hours.

.5th press, "4h" and "6h" light indicators come on, the cycle will

start in 10 hours.

.6th press, "2h" , "4h" and "6h" light indicators come on, the cycle

will start in 12 hours.

.last press, all light indicators will extinguish and you can reset.

After selecting the delay time, the wash cycle can be set, as

explained in "Starting a wash cycle..." There will be a short acous-

tic signal, and at this point the delay period will begin to count

down. During this period the delay indicator light (I) will blink. At

the end of the delay time, the indicator will stop blinking and the

cycle will start.

NOTE:

a) During the delay period, none of the settings can be modified.

If necessary, they can be cancelled by pressing cycle selector

"P" for about 5 seconds.

b) If the power to the appliance goes off or the door is opened

during the delay period, the clock will stop the countdown. It will

start again when the power has come back on, or when the door

has been closed.

Wash Cycle Adjustment Buttons

1/2 Load Button

This button (see" Close-up View-Control Panel", letter "C") makes

it possible to wash dishes using only the upper rack if there are

not enough dishes for a full load, This will allow you to save on

water and electrical energy.

.5.

Wash Cycle Table

Cycle

Selection

Information

Very dirty dishes,

pots and pans. (Not

to be used with deli-

cate items)

Intensive

Normal dirty dishes,

pots and pans. Stan-

dard daily cycle.

Normal Wash

Normal dirty dishes,

pots and pans without

dried on residue.

Light Wash

Economic, fast cycle to be

used for delicate items which

are sensitive to higher. Run

immediately after dishes are

Glassware

used.

Economic, fast cycle to

be used to on not very

dirty dishes right after

they are used. No dry-

ing cycle.

Rapid Wash

Pre-wash of dishes,

pots and pans while

waiting for the load to

be completed after the

Soak

subsequent meal.

The cycle of heat wash-

ing and dry tableware.

Heat wash

Description of

Detergent

Cycle

Pre-wash with hot water.

Extended wash at 70 K

Rinse with cold water.

30g

Rinse with hot waterK

Drying.

Pre-wash with cold water.

Extended wash at 50 .

5+25g

Rinse with cold water.

Rinse with hot water.

Drying.

Pre-wash with cold water.

Extended wash at 50 K

30g

Rinse with cold water.

Rinse with hot waterK

Drying.

Wash at 45 .

Rinse with warm water.

15g

Hot rinse.

Drying.

Short wash at 40 .

15g

Cold rinse.

Short cold wash to prevent

food residue from drying on

the dishes K

Heat washing.

.6.

Rinse Aid

ERF