Daspi ELTRA 400 Manual de instrucciones - Página 6

Navegue en línea o descargue pdf Manual de instrucciones para Sistemas de control Daspi ELTRA 400. Daspi ELTRA 400 7 páginas.

Imprimir página

eneral safety regulations

Thank you for having chosen this product. Your new electro-

mechanical barrier has been produced to a high level of quality

and reliability that guarantees efficiency and safety for a long

period of time. The attachments to this booklet contain all the

necessary information to assemble your barrier and to safeguard

your security.

All our products are constructed according to regulations in force.

During assembly and maintenance operations use only original

spare parts. Avoid accidents by taking the necessary preventative

and prudent actions.

Mportant

It is forbidden to carry out any assembly, repair or adjustment

operations by non qualified personnel and all necessary precautions

must be taken to avoid accidents, such as disconnecting the

power supply (including any buffer batteries present). All moving

parts must be fitted with protection guards.

ATTENTION: Any use not foreseen in this instruction manual

and/or any arbitrary modifications made to this product or its

components, frees DASPI from all responsibility for damage or

harm to persons, animals or property.

Keep this manual and the attached technical file of the installation

in a safe place, known to all personnel so it is available for future

use. Dispose of all packaging materials after installation (boxes,

plastic, polystyrene, etc.) according to regulations in force, paying

special attention to plastic bags that can be extremely dangerous

if children are in the vicinity.

ecurity

ecHaniSm

diStance

in mouVement

ProDuCt tyPe

The ELTRA 400 barrier has been designed and constructed to

open barrier arms up to 4 meters in length. DASPI does not

assume any responsibility for other use than the intended

use of the ELTRA 400 barrier.

ATTENTION: The ELTRA 400 barrier is not equipped with

a mechanical clutch and therefore when installed must be

connected to a special DASPI control unit or to a control unit

equipped with an electronic clutch.

uSe oF tHe MeCHanISM

Important safety instructions

Attention, for personnel safety it is of vital importance to

carry out the following instructions.

Keep these instructions in a safe place. Do not allow children

to play with the fixed or remote controls of the gate. Place

the remote controls out of the reach of children.

As the mechanism can be controlled nearby or at a distance

using push buttons or remote controls it is indispensable

that the efficiency of all safety devices be checked frequently.

We recommend periodical checks (every six months) by

qualified personnel to adjust the electronic clutch. To adjust

this protection device, see the paragraph "Electronic clutch

adjustment" in the instruction manual of the electronic

control unit.

PrelIMInary CHeCkS

• Read carefully all parts of this manual.

• Check that the product was not damaged during

transportation.

englISH

o not inStaLL tHe

Lectric SHocK

automation in pLace fuLL

of expLoSiVe moiStureS

Instruct all personnel involved with operating the mechanism

about the commands and safety systems installed on the plant.

This product cannot be installed in an explosive atmosphere.

aintenance

Disconnect the power supply before carrying out any maintenance

operations. To correctly maintain the plant where the ELTRA 400

barrier is installed, proceed as follows:

Periodically clean the photocell optics.

Charge qualified personnel to adjust the electronic clutch (see

relative paragraph of the electronic control unit installation

manual).

If any malfunction occurs, notify qualified personnel.

eMolition

Demolition must take place according to regulations in force.

Recycled materials must be separated by type (copper, aluminium,

plastic, electrical parts, etc.). No materials considered dangerous

to the handling personnel are present.

isMantling

Proceed as follows to dismantle or transport the mechanism to

another location:

Turn off the power supply and disconnect the electrical plant.

Disassemble the control panel and all the components of the

installation.

If some components are damaged or cannot be removed, substitute

the components.

tHe gLoVeS

• Check that the electrical plant conforms to the characteristics

required by the gear motor.

• Check that an adequate grounding plant exists and that all

metallic parts are connected to this plant.

• We remind you that the mechanism facilitates use of the

barrier and does not resolve problems due to defects, bad

installation or lack of maintenance to the barrier.

luBrICatIon

The ELTRA 400 barriers are supplied with permanent grease

lubrication

InStallatIon

Important safety instructions for installation.

Warning: A bad installation can cause a great deal of damage

or harm. Scrupulously follow all installation instructions.

ATTENTION: For any reason whatsoever never disassemble

the barrier arm when it is in a horizontal position

ATTENTION: For any reason whatsoever never carry out an

emergency or manual manoeuvre if the barrier arm is not

assembled

ATTENTION: Do not release the motor when it's working

For correct commissioning of the ELTRA 400 barriers,

proceed as follows:

Locate the point inside the property where the ELTRA 400

barrier will be installed (figure 1).

Construct a solid concrete base with the dimensions

illustrated on figure 1; provide a passage for the sheath "G"

of the power cables and system controls.

Before the concrete sets, position the "Ps" plate (OPTIONAL)

Se gLaSSeS

eep tHe protection

for WeLding

carter