Duro Dyne DuroZone RED-4 Manual de instrucciones de instalación - Página 8

Navegue en línea o descargue pdf Manual de instrucciones de instalación para Sistemas de control Duro Dyne DuroZone RED-4. Duro Dyne DuroZone RED-4 16 páginas. Zone control system

Imprimir página

Automatic Contractor Test (Version 1.70)

the Automatic Contractor test (ACt) can

be started at any time by pressing and holding

the timer Reset switch for 10 seconds.

the test can be terminated at any time by

pressing the timer Reset switch again.

When the test is started all calls are terminated and

all dampers will be closed. the Status LED will be on

continuously during the test.

Step1. Zone1 Thermostat Test

the DPR1 LED will turn On and

the Cool, Heat, Fan, or EM Heat

LED will turn On indicating the

state of the Zone1 thermostat. If

the Cool, Heat, Fan and EM Heat

LEDs are all Off, there is no call at

the thermostat. Step 1 will run 30

seconds.

Step2. Zone2 Thermostat Test

now the DPR2 LED will turn On

and the Cool, Heat, Fan, or EM

Heat LED will turn On indicating

the state of the Zone2 thermostat.

Step 2 will run 30 seconds.

Step3. Zone3 Thermostat Test

now the DPR3 LED will turn On

and the Cool, Heat, Fan, or EM

Heat LED will turn On indicating

the state of the Zone3 thermostat.

Step 3 will run 30 seconds.

Step4. Zone4 Thermostat Test

now the DPR4 LED will turn On

and the Cool, Heat, Fan, or EM

Heat LED will turn On indicating

the state of the Zone4 thermostat.

Step 4 will run 30 seconds.

Step5. Damper Test

now all of the dampers will be

opened and the indoor fan is

activated. Step 5 will run for 1

minute. You can terminate the

test at this time by pressing the

timer Reset switch. You might want to change

the thermostats and again run the test.

Step6. Damper4 Test

now Damper4 will close and the indoor fan

remains activated. If Damper4 is used as a zone

damper you should not feel airflow at Zone4

and the other zones should be open. the DPR4

LED will be OFF. If Damper4 is used as a fresh

air damper it also should be closed. Step 6 will

take 1 minute.

DuroZone

RED4 - InStALLAtIOn InStRUCtIOnS PAGE 8

RED4 InstrManual-7-1-10.indd 8

Step7. Damper3 Test

now the Damper3 will close and the indoor fan remains

activated. You should not feel airflow at Zone3 and the

other zones should be open. the DPR3 LED will be OFF.

Step 7 will run 1 minute.

Step8. Damper2 Test

now Damper2 will close and the indoor fan remains

activated. You should not feel airflow at Zone2 and the

other zones should be open. the DPR2 LED will be OFF.

Step 8 will take 1 minute.

Step9. Damper1 Test

now Damper1 will close and the indoor fan remains

activated. You should not feel airflow at Zone1 and the

other zones should be open. the DPR1 LED will be OFF.

Step 9 will take 1 minute.

Step10. Stage1 Heating Test

All dampers will be open now and the stage1 heating is

activated. Check that heated air is entering the zones.

the Heat LED will be On continuously. Step 10 will run

1 minute.

Step11. Stage2 Heating Test

now the stage2 heating is also activated. Check that

heated air is entering the zones. the Heat LED will be

blinking. Step 11 will run 1 minute if it is on a Heat

Pump System. Add 1 minute if not on a Heat Pump for

the purge cycle.

Step12. Stage3 Heating Test

If a heat pump is selected, the third stage heating will be

activated for 1 minute. then the heating will be turned

Off and the indoor fan run for 1 minute to purge the

heat. Step 12 will run 2 minutes.

Step13. Stage1 Cooling Test

the Stage1 cooling is now turned On and Cool LED will

be On. Check that cool air is entering the zones. Step 13

will run 1 minute.

Step14. Stage2 Cooling Test

now the Stage2 cooling is also turned On and Cool LED

will blink. Check that cool air is entering the zones. Step

14 will run 1 minute.

After the stage2 cooling has run for 1 minutes the cooling

will be turned Off. the indoor fan will run for 1 minute

to purge the cooling and then the panel will return to

normal operation.

For the most updated product information,

please visit our website

www.durodyne.com

Printed in USA 6/2010

BP035428

7/9/2010 5:34:53 PM