Elsner Corlo Touch KNX 5in WL Especificaciones técnicas e instrucciones de instalación - Página 2
Navegue en línea o descargue pdf Especificaciones técnicas e instrucciones de instalación para Interruptor Elsner Corlo Touch KNX 5in WL. Elsner Corlo Touch KNX 5in WL 2 páginas. Display and touch switch
Imprimir página
2.2.3. Connection overview
1
2
3
4a
5a
4b
6 7
8 5b
9
Fig. 8
7 Programming button for ad-
1 Monting unit
dressing the device at the bus
2 Terminal auxiliary supply 24 V
(recessed)
DC ±10%, terminal configura-
8 Analog/digital inputs socket
tion independent from polarity
9 Ventilation slots
3 Display unit
10 Micro SD socket (card contacts
4 Notches for snaplock
must show in the direction of
5 Aperture für Screw (fixing)
the display when inserting it)
6 KNX terminal bus +/-
Connect the bus voltage (no. 6, red/black terminals) and auxiliary voltage (no. 2,
yellow/white terminals).
Use the attached breakout cable for connecting the digital/analog inputs (no. 8).
The cables for the inputs can be extendet to up to 10 m. All GND connections of the
inputs are bridged internally (black cable).
Fig. 9
Breakout cable for analog/digital inputs:
Input 1: black/white
Input 2: black/yellow
Input 3: black/lilac
Input 4: black/blue
2.3. Instructions for assembly and operational start-up
Never expose the sensor to water (e.g. rain) or dust. This can damage the electro-
nics. You must not exceed a relative air humidity of 95%. Avoid condensation.
After the operating voltage has been applied, the device will enter an initialisation
phase lasting a few seconds. During this phase no information can be received or
sent via the bus.
3.
Addressing the device
The programming mode for addressing at the bus is activated via the programm-
ing button at the back of the housing or via the display.
Settings > System > Service > KNX
KNX programmming LED ON:
Programming mode active.
KNX programming LED OFF:
Programming mode off.
The current address is displayed (Ad-
dress 15.15.250 when delivered).
4.
Setting up the WLAN connection
Only for the Corlo Touch KNX 5in WL model with an interface for wireless net-
work connection!
4.1. WLAN settings in the ETS
The WLAN connection must be set up in the ETS. Consult the WLAN setting section
in the manual
ETS:System Settings > WLAN
2.13.1 WLAN
You set the network name and the encryption for compatibility with the WLAN net-
work access point. The IP address allocation can be made either automatically by
DHCP or manually.
Please note: If an automatic change depending on the quality of the connection
between 2.4/5 Ghz should be possible, you have to set up in the wireless router the
Display Corlo Touch KNX 5in
same Wi-Fi name with the same Wi-Fi password for both frequencies. Otherwise,
only the frequency defined with the access can be used. (From version OPSys 0.1.4
or higher)
4.2. Displaying WLAN status on the display
You can call up information on the current status of the connection on the Corlo
Touch KNX 5in WL display. Network name, signal strength, IP address, DNS ad-
dress and GW address are displayed.
Settings > System > Service > WLAN Status
3.11.7. WLAN Status
10
5.
Maintenance and care
Fingerprints on the glass area and frame are best removed with a cloth moistened
with water or a microfiber cloth. Do not use an abrasive cleaning agent or aggres-
sive cleansing agents.
For cleaning of the screen, the „cleaning mode" can be used, that is activeted via
the display.
Settings > Cleaning Mode
During a period set in the ETS, the touch function is disabled then and the screen
can be cleaned.
6.
Use of the proximity sensor
With the integrated proximity sensor, the screen saver can be deactivated already
when a hand aproaches (fast activation from stand-by) or functions can be trigge-
red via the bus (switching on approach).
To use the proximity sensor for sending communication objects, for example for
switching, set the proximity sensor parameters in the ETS accordingly. See manual
chapter
2.7. Proximity sensor
2
1
The proximity sensor reacts only when a larger ob-
ject moves from the front into the detection area. It
is best to move the flat hand towards the display so
that the sensor reacts quickly.
Fig. 10 Proximity sensor
1 Proximity sensor Sender
2 Proximity sensor Receiver (and light sensor for
7.
Load individual images
7.1. Images for screensaver
The setting of the screen saver is described in the manual chapters
2.4. Display (ETS) and 3.4.4. Screen saver (Display)
Images that are shown as the screensaver must be stored on a micro SD card. In
order that the system can recognize the SD card, carry out a reset in the menu after
inserting it
Settings> System > Reset
This is not necessary if the card was inserted before booting the system. The card
must remain in the device.
Store images in the given size in a corresponding folder on the top level of the SD
card:
Image type
Images for slide
show
Images for
individual image
display
Images for individual image display ("diafix" folder) must have a 4-digit numerical
sequence so that they can be called up in the ETS and in the menu (0001...9999).
7.2. Images for image display
Images can be called up as a stationary display (e. g. welcome screen). In contrast
to the screensaver, the touch function is disabled while a stationary image is di-
splayed.
Images that are to be called up via the "Stationary Image" communication object
must be stored on a micro SD card. In order that the system can recognize the SD
card, carry out a reset in the menu after inserting it
Settings> System > Reset
Display Corlo Touch KNX 5in • Version: 06.04.2020 • Technical changes and errors excepted. • Elsner Elektronik GmbH • Sohlengrund 16 • 75395 Ostelsheim • Germany • www.elsner-elektronik.de • Technical Service: +49 (0) 7033 / 30945-250
adaption of the screen brightness)
Resolution
File format
Folder name
800 × 480 pixels .jpg (RGB mode) slideshow
800 × 480 pixels .jpg (RGB mode) diafix
This is not necessary if the card was inserted before booting the system. The card
must remain in the device.
Store images in the given size in a corresponding folder on the top level of the SD
card:
Image type
Resolution
File format
Stationary images
800 × 480 pixels .jpg (RGB mode) fixed image
Stationary images must have a 4-digit numerical sequence so that they can be cal-
led up in the ETS and in the menu (0001...9999).
7.3. Exchanging images and graphics
For the Corlo Touch KNX 5in display pages, a large number of icons from the
area of security, multimedia, sensors, operation, house, light and air conditioning
and drive control are available and these are stored in the device. However, you
can also use proprietary symbol graphics and rotary control graphics.
Images that are shown as icons must be stored on a micro SD card. In order that
the system can recognize the SD card, carry out a reset in the menu after inserting
it
Settings> System > Reset
This is not necessary if the card was inserted before booting the system. The card
must remain in the device.
Store images in the given size in a corresponding folder on the top level of the SD
card:
Image type
Resolution
File format
Symbol/small icon
96 × 96 pixels
.png
Icons for rotary con-
316 × 320 pixels .png
trol
Icons must have a 4-digit numerical sequence so that they can be called up in the
ETS and in the menu (0001...9999).
2
Folder name
Folder name
icons
icons