Datalogic S62-PA-2/5 Manual de instrucciones - Página 2

Navegue en línea o descargue pdf Manual de instrucciones para Accesorios Datalogic S62-PA-2/5. Datalogic S62-PA-2/5 4 páginas.

Imprimir página

Datalogic S62-PA-2/5 Manual de instrucciones

S62-PL...B Laser

Polarised retroreflex

S62-PL...C Laser

Diffuse proximity

INSTRUCTION MANUAL

S62..B

S62..C

CLASS 1 EN 60825-1

CLASS 2 EN 60825-1

(2014)

LASER PRODUCT

CONTROLS

OUTPUT LED (yellow)

The yellow LED ON indicates the following output status: N.O.

closed and N.C. open.

POWER ON LED (green)

The green LED ON indicates the sensor powering status and

laser emission presence.

SENSITIVITY TRIMMER (ADJ.)

Monoturn trimmer that adjusts the sensitivity and thus the

sensor operating distance.

Please refer to "SETTING" paragraph for the correct use

procedure.

WARNING: the maximum mechanical trimmer rotation is

equal to 240°. Do not apply excessive torque over the

maximum and minimum positions.

INSTALLATION

The sensor can be positioned by

means of the three housing's

holes using two screws (M4x25

or longer, 1.5 Nm maximum

tightening torque) with washers.

Various orientable fixing brackets

to ease the sensor positioning

are available (please refer to the accessories listed in the

general catalogue).The operating distance is measured from

the front surface of the sensor optics.

The M12 connector can be oriented at two different positions

using the specific fastening spring and rotating the block to

180°.

CONNECTIONS

M12 connector

TECHNICAL DATA

S62..B

Power supply:

Ripple:

Consumption

(output current excluded):

Outputs:

PNP or NPN N.O. / N.C.; 30 Vdc max. (short-circuit protection)

Output current:

Output saturation voltage:

Response time:

Switching frequency:

Emission type:

RED LASER Class 1

EN 60825-1 (2014)

Operating distance (typical values):

refer to TAB.1

Min. detectable object dimension:

Indicators:

Setting:

Functioning temperature:

Storage temperature:

Dielectric strength:

Insulating resistance:

Ambient light rejection:

Vibrations:

0.5 mm amplitude, 10 ... 55 Hz frequency, for every axis (EN60068-2-6)

Shock resistance:

Housing material:

Lens material:

Mechanical protection:

Connections:

Weight:

S62...B SETTING

S62...B alignment:

- Position the sensor and reflector aligned on opposite sides at the desired distance.

- Turn to maximum the sensitivity adjustment trimmer (ADJ.) (clockwise).

- Determine the powering on and powering off points of the yellow LED (OUT) by moving

vertically and horizontally the sensor and mount the

sensor in the middle of the points found.

Control:

Enter laterally the object inside the operating

field

and control that the yellow LED turns on.

Remove the object and check that the yellow

LED

turns off immediately

S62...C setting:

Position the sensor and turn the sensitivity trimmer at minimum: the yellow LED is OFF. Place the target opposite

the sensor.

Turn the sensitivity trimmer clockwise until the yellow LED turns ON (Target detected state, pos.A).

Remove the target, the yellow LED turns OFF. Turn the trimmer clockwise until the yellow LED turns ON (Background detected

state, pos.B). The trimmer reaches maximum if the background is not detected.

Turn the trimmer in intermediate position C, between the two positions A and B. The green LED must be ON.

S62...B PERFORMANCES

TAB.1: Operating distances (m)

REFLECTOR (mm)

R7 (51X51)/

R1 (Ø31)

R2 (Ø63)

R6 (60x40)

R20 (Ø63)

0.3 ... 16

0.3 ... 20

0.4 ... 22

0.3 ... 22

Note: The use of the RT 3970 reflecting tape is not suggested.

S62..C

10 ... 30 Vcc

2 Vpp max.

30 mA max

100 mA max (overload and overvoltage protection)

 2 V

200 s

2.5 kHz

RED LASER ( = 645...665 nm): Class 2 EN 60825-1 (2014)

Class II CDRH 21 CFR PART 1040.10Pulsed emission: pot.

max  5 mW; pulse duration = 5s; frequency max = 32 KHz

1m on 90% white target (EG2)

0.5 mm at 0.5m (minimum spot)

OUTPUT LED (YELLOW) / POWER ON LED (GREEN)

Monoturn sensitivity adjustment trimmer

-10 ... 55 °C

-20 ... 70 °C

500 Vac 1 min., between electronics and housing

>20 M 500 Vdc, between electronics and housing

according to EN 60947-5-2

11 ms (30 G) 6 shock for every axis (EN60068-2-27)

ABS

PMMA window, polycarbonate lenses

IP67

M12 4-pole connector

40 g. max.

spot diameter (mm)

(19X10)

0.2 ... 2

distance (mm)

DIMENSIONS

SENSITIVITY TRIMMER

6.18

10.7

POWER ON LED

OUTPUT LED

SAFETY PRECAUTIONS

All the electric and mechanical safety regulations have to be

respected during sensor functioning.

The sensor has to be protected against mechanical damage.

Apply the labels supplied in a visible position near the laser

emission beam.

S62..C:

Do not stare directly into the laser beam!

Do not point the laser beam towards people!

Eye irradiation superior to 0.25 seconds is dangerous.

Please refer to the Class 2 Standard (EN60825-1).

These sensors can not be used for safety applications!

The sensors are NOT safety devices, and so MUST NOT be used

in the safety control of the machines where installed.

Datalogic S.r.l.

Via S. Vitalino 13 - 40012 Calderara di Reno - Italy

Tel: +39 051 3147011 - Fax: +39 051 3147205 - www.datalogic.com

Helpful links at www.datalogic.com: Contact Us, Terms and Conditions,

Support.

The warranty period for this product is 36 months. See General Terms and

Conditions of Sales for further details.

MAX

MIN

Under current Italian and European laws, Datalogic is not obliged to take

care of product disposal at the end of its life. Datalogic recommends

disposing of the product in compliance with local laws or contacting

authorised waste collection centres.

RESERVED.  Without limiting the rights under copyright, no part of this

documentation may be reproduced, stored in or introduced into a retrieval

system, or transmitted in any form or by any means, or for any purpose,

without the express written permission of Datalogic S.p.A. and/or its affiliates.

Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A.

in many countries, including the U.S.A. and the E.U. All other trademarks and

brands are property of their respective owners. Datalogic reserves the right to

make modifications and improvements without prior notification.

826003257 Rev. H

4.7

RECEIVER

EMITTER

M12

Ø15