Frigidaire FCGM201RFB1 Manual de uso y mantenimiento - Página 3

Navegue en línea o descargue pdf Manual de uso y mantenimiento para Frigorífico Frigidaire FCGM201RFB1. Frigidaire FCGM201RFB1 11 páginas. Commercial freezer/refrigerator glass door refrigerator

Imprimir página
Frigidaire FCGM201RFB1 Manual de uso y mantenimiento
Electrical
Information
These
guidelines
must be followed
to ensure
that safety
mechanisms
in the design
of this appliance
will operate
properly.
Avoid fire hazard or
electric shock. Do not use an extension cord
or an adapter
plug.
Do not remove
any
prong from the power cord.
Grounding type
walmreceptacle
Power suppmy
cord with 3-prong
grounding pmug
•
Refer
to the serial
plate
for
correct
electrical
rating.
The
power
cord
of the appliance
is equipped
with
a three-prong
grounding
plug for protection
against
shock
hazards.
It must
be plugged
directly
into its own properly
grounded
three-prong
receptacle,
protected
with a 15 amp time delay fuse or circuit
breaker.
The receptacle
must
be installed
in accordance
with
the local codes and ordinances.
Consult
a qualified
electrician.
Receptacles
with Ground
Fault Circuit
Interrupters
(GFCI)
are
NOT
RECOMMENDED.
DO
NOT
USE
AN
EXTENSION
CORD
OR AN ADAPTER
PLUG.
•
If the
voltage
varies
by
10 percent
or more,
appliance
performance
may
be affected.
Operating
the appliance
with
insufficient
power
can damage
the motor.
Such
damage
is
not covered
under the warranty.
If you suspect
your voltage
is
high or low, consult
your
power
company
for testing.
•
To prevent
the appliance
from
being
turned
off accidentally,
do not plug the unit into an outlet
controlled
by a wall switch
or pull cord.
•
DO NOT pinch,
knot,
or bend the power
cord
in any manner.
Other
Precautions
•
NEVER
unplug
the appliance
by pulling
on the power
cord.
Always
grip
the
plug
firmly
and
pull straight
out from
the
receptacle.
•
To avoid
electrical
shock,
unplug
the
appliance
before
cleaning.
NOTE:
Turning
the control
to "OFF"
turns
off the compressor
but does
not disconnect
power
to other
electrical
components.
CASTER
INSTALLATION
AND SET-UP
(Glass
Door Only)
inspect
the underside
of the cabinet
and packaging
for damage
such as a fork truck
can cause.
If hidden
damage
is found
after
uncrating,
immediately
call the delivery
carrier
and request
an
inspection.
Retain
all packaging
and crating
materials
until the
inspection
is complete.
PARTS AND ACCESSORIES
Check to make sure that you have received the box containing
all of the components
listed
below.
A
CASTER
RAiL (2)
E
WASHER
(4)
B
LOCKING
NUT (8)
F
SPACER
PLATE (2)
C
CARRIAGE
BOLT (8)
G
SWIVEL
CASTER
(2)
D
BOLT (4)
H
FIXED
CASTER
W/ BRAKE
(2)
TOOLS
NEEDED
You will need
the following
tools
to assemble
and
install
the
casters
to the unit.
3/8"
AND
1/2"
INCH
ADJUSTABLE
WRENCH
SOCKET
WRENCH
OR
PLIERS
1/2"
INCH
FIXED
WRENCH
UNCRATING
AND SET-UP
• Remove
carton
and all loose parts
from inside of the unit.
• Carefully
tip the unit onto
its back with the help of an assistant.
Lay the unit gently
to rest on blocks
to avoid
damaging
the
condensate
drain
hose
and the plastic
raceway
that covers
the evaporator
tubing
on the back of the cabinet.
• Remove
and discard
the wood
skid from
the bottom
and the
four (4) screws
using a 3/8" socket
wrench
(see Fig. 1).
• Using
a large
adjustable
wrench,
remove
and discard
the two
(2) black plastic
leg levelers
by turning
it counterclockwise
(see
Fig. 2).
jl
SCREWS
LEG
LEVELER
i!i
Figure 2
Figure 1