AUSTRAL CLOTHES HOISTS FOLDAWAY 51 Manual - Página 2

Navegue en línea o descargue pdf Manual para Electrodomésticos AUSTRAL CLOTHES HOISTS FOLDAWAY 51. AUSTRAL CLOTHES HOISTS FOLDAWAY 51 2 páginas. Foldaway rotary hoists

Imprimir página

FITTING THE HANDLE

(a)

Fit the Handle Shaft to the Handle Grip. Push the split end of the Shaft through the hole at the bottom of the Handle.

When pushed through, the split end will expand and lock into place.

(b)

Clip the Handle Cover onto the back of the Handle by pushing the pins into the locating holes. Press in firmly.

4. TO CONCRETE THE GROUND SOCKET

(a)

Mix quick setting cement according to manufacturer's instructions or alternatively mix concrete in the following

proportions: 3 gravel:1 sand:1 cement with water. Concrete should be damp enough to hold together when squeezed

in the hand.

(b)

Stand the Ground Socket in the centre of the hole and open the Head Section. Check to ensure correct height setting

for user and of the Ground Socket to finished surface level. Adjust if necessary. Fold the arms down and fit the Line

Retainer for final installation. Ensure the handle is facing the correct way (i.e. towards the path).

(c)

Hold the Rotary upright and fill with another 50mm gravel only. Add concrete mix to approximately half depth.

Check to ensure the Mail Column is level, tamp the concrete down using a rod to settle the concrete. Re-check the

Main Column level and then fill the hole to within 20mm from the top. Settle the concrete again and re-check the

level. Finish with a mix of sand and cement (2 sand:1 cement). LEAVE FOR 48 HOURS BEFORE USING.

(B) Important information and Operating Instructions:

It is recommended the Rotary Hoist is removed regularly to ensure free and easy removal from the Ground Socket.

Failure to do so, may cause difficulty in removing the Rotary Hoist when the need arises.

Austral's Warranty does not cover defects caused through the installation or use of a Clothesline Cover or Sunshade.

FOLDING THE ROTARY HOIST

Wind the Head Section down, place your fingers on top of the Bush and

squeeze the Cross and Arms up with your hands (Fig.4). Lift the Latch up

and gently lower the Cross section to fold Arms down. Tie the Line

Retainer around the Arms to ensure lines do not tangle during removal.

2. REMOVING THE HOIST

With Head Section folded and secured, hold the Main Column with

both hands, lift and turn the column clockwise to then remove.

Fit the Socket Cap onto the Ground Socket.

REPLACING THE HOIST

Insert the Rotary Hoist into the Socket and gently lower onto the Pin. Rotate the Main Column until it drops into position.

Rotate anti-clockwise for the column to lock into position.

4. UNFOLDING THE HEAD SECTION

Remove the Line Retainer, grasp the Arms and gently pull them outwards. Raise the Cross up as far as it will go as in

Fig.4 and lower the Latch into the locked position. CAUTION: If the Cross will not lift into position, the cords may

have tangled. Carefully check the lines. NEVER force the Cross into position.

LINE TIGHTENING

To tighten the lines, open the lever on the Line Tension Lock. Start from the inner position, pulling the cords as

you work your way outwards. Pull the Cord Knob tight and lock the lever on the Line Tension Lock back into position.

6. DURING USE

Distribute washing evenly to allow Rotary Hoist to rotate evenly. Wind the Head Section down into the locked position if

hanging washing on windy days. Simply pull on one arm to rotate the Head Section while in this position. When finished,

wind the line up to allow the Head Section to rotate freely in the breeze.

Note: Please contact your local Distributor below for your nearest stockist of spare parts and accessories.

VICTORIA/TASMANIA

NEW SOUTH WALES

STH AUST./ NT

QUEENSLAND

WESTERN AUSTRALIA

Please retain the attached Warranty with details of your receipted purchase.

(03) 97998122

(02) 99581533

(08) 83374445

(07) 55924546

(08) 94551985

Fig.4

March.2017