4x4 TOUGH 21-280467 Manual del usuario - Página 12

Navegue en línea o descargue pdf Manual del usuario para Accesorios para automóviles 4x4 TOUGH 21-280467. 4x4 TOUGH 21-280467 16 páginas. 4wd winch

Imprimir página
4x4 TOUGH 21-280467 Manual del usuario
Motor - Cable connections
T
erminal C (Blue)
Terminal A (Red)
Earth Terminal
Terminal B (Yellow)
1.
Your battery must be kept in good condition.
CAUTION:
2.
Be sure battery cables are not drawn taught across any surfaces which could possibly damage them.
3.
Corrosion on electrical connections will reduce performance or may cause a short.
4.
Clean all connections especially in remote control switch and receptacle.
5.
In salty environments use a silicone sealer to protect from corrosion.
6.
Check electrical cables and connections after each use.
Winch Operation
SUGGESTION:
The best way to get acquainted with how your winch operates is to make a few test runs before you actually need to use it.
Plan your test in advance. Remember you can hear your winch as well as you can see it operate. Get to recognise the
sound of a light steady pull, a heavy pull, and sounds caused by load jerking or shifting. Soon you will gain confidence
in operating your winch and its use will become second nature to you.
OPERATING:
1.
Ensure the vehicle is secure by applying the parking brake or chocking the wheels.
2.
P
ull out the winch rope to the desired length and connect to an anchor point. A suggestion would be a tree trunk
protector wrapped around a suitably sized tree which will not be damaged by the winching operation.
The winch clutch allows rapid uncoiling of the rope for hooking onto the load or anchor point. The shifter tab located on
the gear housing of the winch operates the clutch as follows:
a) To disengage the clutch, move the clutch shifter tab to the DISENGAGE position. Rope may now be free spooled off the drum.
b) To engage the clutch, move the clutch shifter tab into the ENGAGE position. The winch is now ready for pulling.
3.
Re-check all rope rigging before proceeding.
4.
Plug in the winch remote hand control (see Page 10 for instructions). It is recommended that the winching operation
takes place from the driver's position to ensure safe operation.If using the wireless remote control always ensure
that you are located at a distance which is greater than 1.5 times the length of the exposed cable.
5.
Turn the winch on by turning the on / off orange switch to the on position (clockwise)
6.
To commence winching operation, start vehicle engine, select neutral in transmission
and maintain engine speed at idle.
7.
Operate the remote control switch to IN or OUT until the vehicle has been retrieved.
Stop the winch regularly to ensure that the rope is winding onto the drum evenly.
•
Check the winch carefully and thoroughly before operating.
CAUTION:
Never winch
•
Never wrap the rope around the object and hook onto the rope itself. This can cause damage to the object being
•
pulled, and kink or fray the rope.
Keep hands, clothing, hair and jewellery clear of the drum area and rope when winching.
•
Never use the winch if the rope is frayed, kinked or damaged.
•
•
Never allow anyone to stand near the rope, or in line with the rope while it is under load. If the rope
should slip or brake,it can suddenly whip back along the line of pull, causing a hazard for anyone in the area.
Always stand well to the side while winding.
•
• ALWAYS disengage the winch when not in use.
12
with your vehicle in gear or in park. This would damage your vehicle's transmission.
Control Box - Cable connections
To motor Terminal B
To motor Terminal A (Red)
(Yellow)
To motor
Terminal C
(Blue)
To motor
Earth Terminal
.
.
To positive(+)
terminal of
battery
To negative(-)
To motor
terminal of
Earth Terminal
battery
OFF
ON