BENDIX SmarTire Instrucciones de instalación

Navegue en línea o descargue pdf Instrucciones de instalación para Accesorios para automóviles BENDIX SmarTire. BENDIX SmarTire 4 páginas.

Imprimir página

SmarTire

Tire Pressure Monitoring System (TPMS) by Bendix CVS

Replacement Service Kit

KIT COMPONENTS

The following components are in the SmarTire

Pressure Monitoring System (TPMS) by Bendix CVS

service kit:

Component

Electronic Control Unit (ECU)

Washer

Nut

Patch Cable

BACK UP THE CURRENT TPMS SETTING

1. If the current Electronic Control Unit (ECU) can

communicate on the CAN bus, use the Bendix

PRO

diagnostic software connected to the vehicle

™

diagnostic port.

2. Select the Bi-Directional tool bar icon, and then start

the TPMS Backup and Restore application.

3. Select the Save Settings button to create a backup of

the ECU parameters to your computer.

REMOVING THE PREVIOUS ECU

1. Unscrew the existing antenna connector from the

ECU (1). See Figure 1.

2. Unplug the main harness from the existing TPMS

ECU (2).

Figure 1 - Removing the Previous ECU

Tire

Quantity

ACom

GENERAL SAFETY GUIDELINES

WARNING! PLEASE READ AND

FOLLOW THESE INSTRUCTIONS

TO AVOID PERSONAL INJURY OR DEATH:

When working on or around a vehicle, the following

guidelines should be observed AT ALL TIMES:

▲Park the vehicle on a level surface, apply the parking

brakes, and always block the wheels. Always wear personal

protection equipment.

▲Stop the engine and remove the ignition key when working

under or around the vehicle. When working in the engine

compartment, the engine should be shut oﬀ and the ignition

key should be removed. Where circumstances require that

the engine be in operation, EXTREME CAUTION should be

used to prevent personal injury resulting from contact with

moving, rotating, leaking, heated, or electrically charged

components.

▲Do not attempt to install, remove, disassemble, or

assemble a component until you have read, and thoroughly

understand, the recommended procedures. Use only the

proper tools and observe all precautions pertaining to use

of those tools.

▲If the work is being performed on the vehicle's air brake

system, or any auxiliary pressurized air systems, make

certain to drain the air pressure from all reservoirs before

beginning ANY work on the vehicle. If the vehicle is

equipped with a Bendix

AD-IS

DRM

dryer reservoir module, a Bendix

™

or AD-HFi

air dryer, be sure to drain the purge reservoir.

™

▲ Following the vehicle manufacturer's recommended

procedures, deactivate the electrical system in a manner

that safely removes all electrical power from the vehicle.

▲Never exceed manufacturer's recommended pressures.

▲Never connect or disconnect a hose or line containing

pressure; it may whip and/or cause hazardous airborne

dust and dirt particles. Wear eye protection. Slowly open

connections with care, and verify that no pressure is

present. Never remove a component or plug unless you are

certain all system pressure has been depleted.

▲ Use only genuine Bendix

components, and kits. Replacement hardware, tubing, hose,

ﬁ ttings, wiring, etc. must be of equivalent size, type, and

strength as original equipment and be designed speciﬁ cally

for such applications and systems.

▲Components with stripped threads or damaged parts should

be replaced rather than repaired. Do not attempt repairs

requiring machining or welding unless speciﬁ cally stated

and approved by the vehicle and component manufacturer.

▲Prior to returning the vehicle to service, make certain all

components and systems are restored to their proper

operating condition.

▲ For vehicles with Automatic Traction Control (ATC), the ATC

function must be disabled (ATC indicator lamp should be

ON) prior to performing any vehicle maintenance where

one or more wheels on a drive axle are lifted oﬀ the ground

and moving.

▲The power MUST be temporarily disconnected from the

radar sensor whenever any tests USING A DYNAMOMETER

are conducted on a vehicle equipped with a Bendix

Wingman

system.

▲You should consult the vehicle manufacturer's operating

and service manuals, and any related literature, in

conjunction with the guidelines above.

air dryer system, a Bendix

AD-9si

, AD-HF

brand replacement parts,