BENDIX BA-921 COMPRESSOR-STD-CLOSED ROOM Instrucciones de instalación

Navegue en línea o descargue pdf Instrucciones de instalación para Compresor de aire BENDIX BA-921 COMPRESSOR-STD-CLOSED ROOM. BENDIX BA-921 COMPRESSOR-STD-CLOSED ROOM 4 páginas. Air power compressor
También para BENDIX BA-921 COMPRESSOR-STD-CLOSED ROOM: Datos del servicio (17 páginas)

Imprimir página

Bendix

BA-921

Compressor Gear Replacement for Detroit

Engines DD13

and DD15

GENERAL

For genuine Bendix remanufactured compressors not

equipped with a drive gear, it is necessary to remove the

existing gear from the old compressor and reinstall it on the

new remanufactured compressor.

NOTE: It may be necessary to remove the fittings from the

cylinder head prior to removing the gear to prevent damage.

IMPORTANT

The Bendix remanufactured compressor is equipped with

a new safety valve. Do not reuse the old safety valve.

KIT COMPONENTS

•

Genuine Bendix remanufactured BA-921 Compressor

(including safety valve)

GEAR REPLACEMENT PROCEDURE

1. After removing the old compressor from the engine,

place the compressor with drive gear facing upward so

it can be removed safely. NOTE: It may be helpful to

secure the compressor and gear so that the gear does

not rotate and the lock nut can be removed more easily.

See Figure 1.

Figure 1 – Remove the Bendix

BA-921

Compressor

Diesel Corporation (DDC)

GENERAL SAFETY GUIDELINES

WARNING! PLEASE READ AND

FOLLOW THESE INSTRUCTIONS

TO AVOID PERSONAL INJURY OR DEATH:

When working on or around a vehicle, the following

guidelines should be observed AT ALL TIMES:

▲Park the vehicle on a level surface, apply the parking

brakes, and always block the wheels. Always wear personal

protection equipment.

▲Stop the engine and remove the ignition key when working

under or around the vehicle. When working in the engine

compartment, the engine should be shut oﬀ and the ignition

key should be removed. Where circumstances require that

the engine be in operation, EXTREME CAUTION should be

used to prevent personal injury resulting from contact with

moving, rotating, leaking, heated, or electrically charged

components.

▲Do not attempt to install, remove, disassemble, or

assemble a component until you have read, and thoroughly

understand, the recommended procedures. Use only the

proper tools and observe all precautions pertaining to use

of those tools.

▲If the work is being performed on the vehicle's air brake

system, or any auxiliary pressurized air systems, make

certain to drain the air pressure from all reservoirs before

beginning ANY work on the vehicle. If the vehicle is

AD-IS

equipped with a Bendix

DRM

dryer reservoir module, a Bendix

™

or AD-HFi

air dryer, be sure to drain the purge reservoir.

™

▲ Following the vehicle manufacturer's recommended

procedures, deactivate the electrical system in a manner

that safely removes all electrical power from the vehicle.

▲Never exceed manufacturer's recommended pressures.

▲Never connect or disconnect a hose or line containing

pressure; it may whip and/or cause hazardous airborne

dust and dirt particles. Wear eye protection. Slowly open

connections with care, and verify that no pressure is

present. Never remove a component or plug unless you are

certain all system pressure has been depleted.

▲ Use only genuine Bendix

components, and kits. Replacement hardware, tubing, hose,

ﬁ ttings, wiring, etc. must be of equivalent size, type, and

strength as original equipment and be designed speciﬁ cally

for such applications and systems.

▲Components with stripped threads or damaged parts should

be replaced rather than repaired. Do not attempt repairs

requiring machining or welding unless speciﬁ cally stated

and approved by the vehicle and component manufacturer.

▲Prior to returning the vehicle to service, make certain all

components and systems are restored to their proper

operating condition.

▲ For vehicles with Automatic Traction Control (ATC), the ATC

function must be disabled (ATC indicator lamp should be

ON) prior to performing any vehicle maintenance where

one or more wheels on a drive axle are lifted oﬀ the ground

and moving.

▲The power MUST be temporarily disconnected from the

radar sensor whenever any tests USING A DYNAMOMETER

are conducted on a vehicle equipped with a Bendix

Wingman

system.

▲You should consult the vehicle manufacturer's operating

and service manuals, and any related literature, in

conjunction with the guidelines above.

air dryer system, a Bendix

AD-9si

, AD-HF

brand replacement parts,