Dymo 2000 Manual del usuario - Página 3
Navegue en línea o descargue pdf Manual del usuario para Etiquetadora Dymo 2000. Dymo 2000 5 páginas. Electronic labelmaker
Imprimir página
• Press and hold to scan quickly through the text.
• Press
+
or
beginning or end of the line of text.
• When used in conjunction with certain function keys,
use
or
to select options.
• To insert characters into the text, use
position the cursor under the character to the right of
the insertion point, then type in the characters required.
• Press
or
to move the cursor to the start of
the previous or next line of a multi-line label.
• Press
+
or
beginning or end of the label.
PRINTING
PRINT
• Press
to print the label.
PRINT
E
• Use cutter lever
see page 2.
INCREMENTAL PRINTING
Prints the label, then increments a number label by 1,
ready for the next print command. Note that barcode
numbers are not incremented.
SPACE KEY
• Press
to insert a space into the text.
SYMBOL
SYMBOLS
+
JUST
• Press to select a symbol character – see SYMBOLS
AND SPECIAL CHARACTERS and the symbols table
on page 2.
TEXT SIZE
SIZE
• The display shows the current selection of text print
size:
small height
medium height
large height
• Large height is available on 19mm labels only.
Medium height is available on all except 6mm labels.
Small height is available on all labels.
• Press
repeatedly to select the size symbol
SIZE
required.
JUSTIFY
JUST
Labels are normally printed with the text left-justified.
On multi-line labels, press
right-justified or centred text, as shown in the display.
See also LABEL LENGTH.
VERTICAL TEXT
VERT
• Rotates the text through 90° so that the label is
printed
VERT indicator in the display.
• Press again to cancel and return to horizontal text.
Note: Vertical text is not available on multi-line labels.
to move the cursor to the
or
to move the cursor to the
to release and tab-cut the label –
123.N
+
PRINT
small height, extended
medium height, extended
large height, extended
to select left-justified,
JUST
, as confirmed by the
MULTI-LINE PRINTING
• Press
label, e.g.
This is a two
printed as:
to
This is a two
line label
Labels can be created as follows:
6mm
9mm
9mm
1 line medium text
12mm
12mm 1 line medium text
The line indicator in the display will confirm the
number of lines in the label.
BOXED/UNDERLINED PRINTING
The display shows the current selection.
• Press
(confirmed by the A indicator in the display).
• Press a second time to underline all the text on the
label (confirmed by the A indicator in the display).
• Press a third time to cancel and return to normal
text.
ITALIC
• Press once to print the label in italic text (confirmed
by the A indicator in the display).
Press again to cancel and return to normal text.
LABEL LENGTH
• Press to display the current label length. The length
is normally calculated automatically, according to
the length and size of the text on the label. The
justify symbol will also be displayed.
• Press
changing the length, or:
• Press
required, as confirmed by the justify symbol in the
display.
• Use
decrease the length in 2mm steps. The display will
flash if you try to make the label shorter than
the text.
• If the length displayed is preceded by the > symbol,
the length has already been fixed; the label is too
short for the text and it will not print. Either press
to increase the length in 2mm steps until the >
symbol disappears, or press
fixed length; the label is now long enough for the
text and can be printed.
• Press
confirmed by the l<->l indicator in the display, or
4
to start the next line of text on a multi-line
line label in the display will be
and the display will
indicate 2 lines:
19mm
1 line small text
Up to 2 lines
small text
19mm
Up to 2 lines
small text
19mm
once to put a line box around the label
BOX/UL
ITALICS
+
BOX/UL
LENGTH
+
SIZE
to exit the length function without
DEL
if necessary to select the justification
JUST
or
to increase (up to 5000mm max.) or
to fix the length for all subsequent labels,
1
2
3
Up to
4 lines
small
text
Up to 2 lines
medium text
1 line large text
BOX/UL
CLEAR
+
to cancel
DEL