HHP PBNU-LD20P100 Manual de instrucciones de instalación - Página 4
Navegue en línea o descargue pdf Manual de instrucciones de instalación para Horno HHP PBNU-LD20P100. HHP PBNU-LD20P100 20 páginas. Gas-fired furnaces high-efficiency upflow condensing models
Imprimir páginaInspect the venting system for proper size and horizontal
2
�
pitch, . a s required in the National Fuel Gas Code, ANSI
3.
or the CAN/CGA B
Z22
1
these instructions. Determine that there is no blockage or
restriction, leakage, corrosion or other deficiencies which
could cause an unsafe condition;
3 . In so far as is practical, close all building doors and
windows and all doors between the space in which the
appliance (s) connected to the venting system are located
and other spaces of the building . Tum on clothes dryers
and any appliance not connected to the venting system.
Tum on any exhaust fans, such as range hoods and
bathroom exhausts, so they will operate at maximum
speed. Do not operate a summer exhaust fan. Close
fireplace dampers;
Follow the lighting instructions. Place the appliance �eing
4.
inspected in operation. Adjust the thermostat
shall operate continuously;
Test for draft hood equipped appliance spillage at the draft
5.
hood relief opening after
tion. Use the flame of a match or candle;
After it has been determined that each appliance con
6.
nected to the venting system properly vents when tested
as outlined above, return doors, windows, exhaust fans,
fireplace dampers and any other gas burning appliance to
their previous conditions of use;
If improper venting is observed during any of the above
7.
tests, the venting system must
8. Any corrections to the common venting system must
accordance 'Nith the appropriate tables in Appendix G of the
National Fuel Gas Code
Installation Codes. If the common vent system must
resized, it should
resized to approach the minimum size
be
as determined using the appropriate tables of the above
codBs. An improperly sized venting system could result in
the formation of condensate and leakage or spillage of
combustion products.
CLEARANCES TO COMBUSTIBLES
�{
Minimum clearances fro
combustible construction are in
inches:
��b�t:::::::::::::::::::::::::::::::::::::::::::::::::::::: �
Vent Piping
. .
.
.
...
. .
..
Rear
··-·······-··········· ···-·········"
Sides
•..•...•.•.•••..•••..•.. · ..
CLEARANCES FOR ACCESS
Ample clearances should be provided to pert'!lit easy access to
the unit. The followi119 minimum clearances are recommended:
Twenty�four
inches
1.
{24)
and an adjacent wall or another appliance, when access
is required for servic in- g and cleani ng.-
Eighteen ('18) inches at the side where acc
2.
for passage to the front when servicing or for inspection or
replacement of flue/vent connections.
Installation Codes and
149
appliance
so
minutes of main burner opera
5
corrected;
be
be
and!
CANICGA-B
Z22 3 .1
or
149
SPECIFIC UNIT INFORMATION
0
.
...
...
.
.
....
....
...
......
...
..
...
0
:.;;.
•••••• _ • •••
0
.
..
.
.
....
.
..
.
..
.......
.
...
.
.
the front of, t he furnace
between
e'�
Is required
. LIMITATIONS & LOCATION
This furnace �h?uld
be
and local butld1ng/safety _codes and requirements, or in the
absence of local codes, with the National Fuel Gas Code
Z223.1 or C�N/CGA-B
focal plumbrng or waste water codes, and other
codes.
CAUTION: Do not install the furnace in an unconditi oned space
or garage that could experience ambient tempe ratures
3Z'F (0"8) or lower.
CAUTION: This unit must be installed in a level ( 1/4
side-to-side and front-to-back to provide proper conden
sate drainage.
CAunON: Do not allow retum air temperature to be below 55 oF
i
for extended per
ods
occur in the main fired heat exchanger.
WARNING: Furnaces shall not be installed directly on carpeting,
tile or other combustible material other than wood
WARNING: Furnace shall be installed so the electrical compo
nents are protected from water.
WARNING: This appliance is not to be used for termporary
heating of buildings or structures under construction.
The size of the unit should
calculation for the structure.
Check the rating plate to make certain the unit is equipp€d for
the type of gas supplied, and proper electrical characteristics
are available.
in
For installations above
feet above sea level. In Canada, derate input 1
1
,000
elevations at
2,000-4,500
be
WARNING: Do not install this unit in a mobile home.
A furnace installed in a residential garage shall
that all burners and burner ignition devices are located not less
that 18" above the garage floor, and located or protected to
prevent damage by vehicles.
NOTE: In all cases, accessibility c learances shall take prece
dence over clearances for combustible materials v.11 e r e
accessibi/fty clearances are greater.
NOMENCLATURE
installed in accordance with all national
Installation Codes (latest editions),
149
.
To do so may ceuse condensa te to
based on an acceptable heat loss
be
feet, reduce input
2,000
4%
feet.
be
Nom. Capacity
{MBH
Gas Type
N = Natural Gas
P = Propane
(LP)
Drive Type
&
CFM
D =Direct
Voltage Code
Product Identifier.
NU = Upflow, (90+ A FUE )
Product Generation
Product Category
P =Furnace
6S0.65·N2
ANSI
applicable
of
·;position
flooring.
for each
for
0%
located so
,/
Input)
.
{x1 00)
3