Gage Bilt GB7720 Información sobre la herramienta de instalación - Página 8

Navegue en línea o descargue pdf Información sobre la herramienta de instalación para Remachadoras Gage Bilt GB7720. Gage Bilt GB7720 10 páginas. Hydraulic installation tool
También para Gage Bilt GB7720: Manual (9 páginas)

Imprimir página

TROUBLE SHOOTING

Providing all maintenance conditions have been met, follow this systematic approach to diagnosis.

1. NO OPERATION WHEN AIR ACTUATOR IS DEPRESSED

a.) Check Powerunit power source.

b.) Control cord may be loose or damaged.

c.) Faulty air actuator. Replace.

d.) Check hydraulic couplings; repair or replace.

2. SLOW OR PARTIAL OPERATION WHEN AIR ACTUATOR IS DEPRESSED

a.) Low hydraulic pressure. Check powerunit, adjust.

b.) Cylinder Piston Rings (8) & (9) could be worn or damaged. Replace.

c.) Excessive wear or scoring on moving parts. Check and replace faulty parts.

3. TOOL OPERATES IN REVERSE

a.) Tool stops in back position. Hydraulic hoses are reversed. Correct.

4. HYDRAULIC OIL OVERHEATS

a.) Powerunit motor rotation reversed. Electrical connections reversed. See powerunit instruction manual.

b.) Restrictions in either hydraulic lines, hoses or couplings. Check and tighten, clean or replace. (See hydraulic

thread preparation pg.5)

5. OIL LEAKAGE

a.) Hydraulic oil leaks from connections. Tighten threaded connections. (See hydraulic thread preparation pg.5)

b.) Oil leaks from tool. Determine source of leak and replace worn or defective o'rings and back-up rings.

6. PINTAIL GROOVES STRIPPED DURING PULL STROKE

a.) Nose Assembly must be pushed onto fastener fully.

b.) Chips may have collected in the puller. Disassemble nose assembly, clean puller in mineral spirits using a sharp

pointed object.

c.) Puller may be worn or damaged. Replace.

d.) Incorrect fastener.

OVERHAUL

WARNING:

DISCONNECT TOOL FROM ITS POWER SOURCE BEFORE PERFORMING OVERHAUL

If a tool is performing poorly or leaking, a complete overhaul may be necessary. Service Kit 772001 contains a com-

plete set of o'rings, back-up rings and screws.

Wrench 750150 (sold separately) is recommended for complete tool overhaul.

Perform overhaul in a clean, well lit area using care not to scratch or nick any smooth surface that comes in contact

with an o'ring. Use of Lubriplate® (Gage Bilt part no. 402723) or other lubricant is recommended during reassembly to

prevent tearing or distorting of o'rings.

Disconnect hydraulic hoses (25) and electrical cord (29) from powerunit. Remove couplers (26 & 27) from hoses (25)

and drain. Remove nut (1), split ring (2) and nose assembly. Using wrench (750150 sold separately) remove front

gland (1). Remove cap (17) and push piston assembly (10) rearward to expose rear piston (14) and remove. Push

front piston assembly (10) out front of cylinder (11).

To remove hoses, remove couplers (26 & 27), remove socket head cap screws (21), washers (18) and slide handle (24)

off.

Clean parts in mineral spirits or other o'ring compatible solvent being sure to clean o'ring grooves. Inspect compo-

nents for scoring, excessive wear or damage.

Reassembly sequence is opposite of disassembly. Be sure relative positions of o'rings and back-up rings are as

shown in exploded view and part list. Relief valve must be installed with four flats towards the rear of the cylinder.

Coat hose fitting threads with a non-hardening teflon thread compound such as Slic-tite® (Gage Bilt part no. 403237).

Apply hot glue to wire connections to ensure wires DO NOT contact each other or handle ass'y. See hydraulic thread

preparation pg.5)

S/N: 1004 AND ABOVE

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

Rev. 6/14