Gaggenau BO 280-630 Manual de instrucciones de instalación - Página 4

Navegue en línea o descargue pdf Manual de instrucciones de instalación para Horno Gaggenau BO 280-630. Gaggenau BO 280-630 20 páginas. 30" built-in single oven
También para Gaggenau BO 280-630: Especificaciones (1 páginas)

Imprimir página

Ausbau

Gerät spannungslos machen. Befestigungsschrauben

lösen.

Gerät leicht anheben und ganz herausziehen.

Important Notes

The appliance is only guaranteed safe to use if installed by

a specialist in accordance with these installation

instructions. Shock protection must be guaranteed by the

installation.

The installer is liable for any damage resulting from

incorrect installation.

The appliance may only be connected by a licensed

specialist. The local electricity supplier's regulations and

construction regulations apply.

Check the appliance for any transport damage.

The appliance must be disconnected from the electricity

before any installation work takes place.

Preparing the Cabinet – Figure 1 + 2

Fitted units must be heat-resistant up to 90 °C, adjacent

unit fronts up to at least 70 °C.

A ventilation cut-out must be made in the intermediate floor

of the cabinet. See figure for dimensions (min. 20 x

500 mm).

Cut out the units before fitting the hob. Remove shavings

as they can affect the function of electrical components.

Secure furniture which is not fitted to the wall using a

standard fixture.

Install the appliance low enough to allow baking trays to be

easily removed.

Electrical Connection

Observe rating plate data for voltage and total rating.

Impor tant : Only connect in accordance with the

connection diagram. Fit the enclosed copper bridges as

required.

Mains connection lead: Type H05 VV-F or higher. The

yellow-green lead for the earth connection must be 10 mm

longer on the appliance side than the other leads.

The rear of the oven has tapered edges. When cabinet

depth is 550 mm, the connection lead must be guided

down the rear right side of the cabinet to the connector

box. Position connector box beneath the cabinet recess.

Do not trap the connection lead during installation and do

not guide it over sharp edges.

The appliance corresponds to safety class I and may only

be used in conjunction with a safety earth terminal.

Fuse protection using B or C circuit breakers is required.

An all pin isolating switch with a contact gap of at least

3 mm must be installed.

Corner installation – Figure 3

Observe space requirements of door and door handle

when planning drawers beside the appliance:

measurement cabinet edge – door panel: 47 mm.

measurement cabinet edge – door handle edge: 94 mm

Observe a minimum opening angle of 90° for corner

installation.

Installation – Figure 4

Impor tant : Do not lift the appliance by the door, door

handle or lower air vent. Lift the appliance by the

installation handles on both sides. Remove installation

handles before installing in cabinet.

Insert the appliance in the cabinet and align it centrally and

horizontally.

Leave an air gap of at least 5 mm between the appliance

and the front of other cabinets.

Secure the appliance at the bottom on both sides with the

screws provided.

If there is no fitted shelf above the oven in the cabinet,

secure the oven against tipping over when the door is

opened. Fit two standard angles 5 mm above the

appliance at 450 mm depth inside the cabinet.

When installing two ovens side-by-side, the door handles

must be in the centre.

Combination with Steam Oven

BS 270/271

The steam oven BS 270/271 is fitted with the controls on

the bottom. Therefore it is particularly suitable for

installation above a Gaggenau series BO 2.. oven.

The rear of the series BO 2.. ovens has tapered edges.

Guide the water inlet hose and the drainage hose on the

rear left side of the cabinet down to the connections.

Fit the steam oven first. Follow the installation instructions

for the steam oven.

When installing an oven and a steam oven side-by-side, the

door handles must be in the centre.

Combination with Warming Drawer

WS 2..

Fit the warming drawer first. Follow the installation

instructions for the warming drawer.

Slide the oven into the cabinet, on top of the warming

drawer.

Impor tant : When installing the oven take care not to

scratch the panel or the handle of the warming drawer.

Removal

Disconnect the appliance from the power supply. Loosen

the securing screws.

Lift the appliance slightly and pull it out completely.