Dynabrade 52413 Instrucciones importantes de funcionamiento, mantenimiento y seguridad - Página 2
Navegue en línea o descargue pdf Instrucciones importantes de funcionamiento, mantenimiento y seguridad para Sander Dynabrade 52413. Dynabrade 52413 4 páginas. 3" disc sander
También para Dynabrade 52413: Instrucciones de uso (4 páginas)
Imprimir página
Important Operating, Maintenance and Safety Instructions
Carefully read all instructions before operating or servicing any Dynabrade
Warning:
Hand, wrist and arm injury may result from repetitive work motion and overexposure to vibration.
Important:
All Dynabrade Rotary Vane air tools must be used with a Filter-Regulator-Lubricator to maintain all warranties.
Warning:
Eye, face, respiratory, sound and body protection must be worn while operating power tools. Failure to do so may result in serious injury or
death. Follow safety procedures posted in workplace.
1.
With power source disconnected from tool, securely fasten abrasive/accessory on tool.
2.
Install air fitting into inlet bushing of tool.
damaging valve body housing.
3.
Connect power source to tool. Be careful not to depress throttle lever in the process.
4.
Check tool speed with tachometer. If tool is operating at a higher speed than the RPM marked on the tool or operating improperly, the tool should be
serviced to correct the cause before use.
1.
Check tool speed regularly with a tachometer. If tool is operating at a higher speed than the RPM marked on the tool, the tool should be serviced to
correct the cause before use.
2.
Some silencers on air tools may clog with use. Clean and replace as required.
3.
All Dynabrade Rotary Vane air motors should be lubricated. Dynabrade recommends one drop of air lube per minute for each 10 SCFM (example: if
the tool specifications state 40 SCFM, set the drip rate of your filter-lubricator at 4 drops per minute). Dynabrade Air Lube (P/N
is recommended.
4.
An Air Line Filter-Regulator-Lubricator must be used with this air tool to maintain all warranties. Dynabrade recommends the following:
Filter-Regulator-Lubricator — Provides accurate air pressure regulation, two-stage filtration of water contaminants and micro-mist lubrication of
pneumatic components. Operates 40 SCFM @ 100 PSIG has 3/8" NPT female ports.
5.
Use only genuine Dynabrade replacement parts. To reorder replacement parts, specify the
6.
A Motor Tune-Up Kit (P/N
7.
Mineral spirits are recommended when cleaning the tool and parts. Do not clean tool or parts with any solvents or oils containing acids, esters,
keytones, chlorinated hydrocarbons or nitro carbons.
Products offered by Dynabrade should not be converted or otherwise altered
from original design without expressed written consent from Dynabrade, Inc.
Important:
User of tool is responsible for following accepted safety codes such as those published by the American National Standards Institute (ANSI).
Operate machine for one minute before application to workpiece to determine if machine is working properly and safely before work begins.
Always disconnect power supply before changing abrasive/accessory or making machine adjustments.
Inspect abrasives/accessories for damage or defects prior to installation on tools.
Please refer to Dynabrade's Warning/Safety Operating Instructions Tag (Reorder No.
Warning:
Hand, wrist and arm injury may result from repetitive work, motion and overexposure to vibration.
All Dynabrade motors use the highest quality parts and metals available and are machined to exacting tolerances. The failure of quality pneumatic motors can
most often be traced to an unclean air supply or the lack of lubrication. Air pressure easily forces dirt or water contained in the air supply into motor bearings
causing early failure. It often scores the cylinder walls and the rotor blades resulting in limited efficiency and power. Our warranty obligation is contingent
upon proper use of our tools and cannot apply to equipment which has been subjected to misuse such as unclean air, wet air or a lack of lubrication during
the use of this tool.
Following the reasonable assumption that any inherent defect which might prevail in a product will become apparent to the user within one year from the date
of purchase, all equipment of our manufacture is warranted against defects in workmanship and materials under normal use and service. We shall repair or
replace at our factory, any equipment or part thereof which shall, within one year after delivery to the original purchaser, indicate upon our examination to have
been defective. Our obligation is contingent upon proper use of Dynabrade tools in accordance with factory recommendations, instructions and safety prac-
tices. It shall not apply to equipment which has been subject to misuse, negligence, accident or tampering in any way so as to affect its normal performance.
Normally wearable parts such as bearings, sanding pads, rotor blades, etc., are not covered under this warranty.
Model
Motor
Number
HP (W)
52413
.7 (522)
52414
.7 (522)
52415
.7 (522)
Additional Specifications: Air Inlet Thread 1/4" NPT • Hose I.D. Size 3/8" (10 mm)
Important:
Secure inlet bushing of tool with a wrench before attempting to install the air fitting to avoid
96045
) is available which includes assorted parts to help maintain motor in peek operating condition.
Motor
Sound
Maximum Air Flow
RPM
Level
CFM/SCFM (LPM)
15,000
76 dB(A)
4/29 (821)
18,000
80 dB(A)
4/32 (906)
20,000
77 dB(A)
5/35 (991)
Abrasive Power Tool.
®
Model #
95903
) for more complete safety information.
Air Pressure
Spindle
PSIG (Bars)
Thread
90 (6.2)
3/8"-24 male
90 (6.2)
3/8"-24 male
90 (6.2)
3/8"-24 male
(PD00•81)
2
95842
Serial #
RPM
,
, and
of your machine.
Weight
Length
Pound (kg)
Inch (mm)
2.3 (1.0)
8-1/8 (206)
2.3 (1.0)
8-1/8 (206)
2.3 (1.0)
8-1/8 (206)
: 1pt. 473ml.)
11405
Air Line
Height
Inch (mm)
5-1/2 (140)
5-1/2 (140)
5-1/2 (140)