ADELSYSTEM MRF102 Manual de instrucciones - Página 3

Navegue en línea o descargue pdf Manual de instrucciones para Disyuntores ADELSYSTEM MRF102. ADELSYSTEM MRF102 3 páginas. 2- channels electronic circuit breaker

Imprimir página
7
Technical data
Input Data
Supply voltage / at DC / Rated
value
DC Input Voltage range (Vdc)
Overvoltage overload capability
Input current / at rated input
voltage 12 - 24 V / Rated Value
Maximum current consumption
Required Back Up Fuse
Input Voltage Reset Output
Output Data
Voltage curve / at output
Drop Out
Number of outputs
Output current / up to 60 °C / per
output / rated value
Adjustable switch Off out current
Type of response value setting
Parallel switching of outputs
Bridging of equipment's
Start Up
Surge voltage shutdown load
circuit
Max Capacitive Load
Rated Surge Voltage
Efficiency
Efficiency
Power loss [W] (max)
Power dissipation
Switching - off per output
Iout = 1.0 ...1.5 x set value
Iout = 1.5 ...1.8 x set value
Iout = 1.2 ...2 x set value
Iout > 2 x set value
Iout > set value and Vin < 15%
(24V); (12V)
Turn On Output after Switch Off
Waiting time after switch off Out
Protection and Monitoring
Internal Fuse protection type
Dielectric strength
Display version
Connection for monitoring
device:
Configuration Aux1
Diagnosis
Connection
Input 12 or 24V
Input 0V
Outputs
Signal Output:
Ambient Conditions
Nominal Temperature
operation
Ambient Temperature
operation
Ambient Temperature Storage
Humidity at 25 °C, no
condensation
Vibration (operation) IEC
60068-2-6
Altitude: 0 to 2 000m - 6560
to 20 000ft
12 – 24 V
8 – 35 V
35 V
20 A max (30A peak max 10
sec)
10mA (12 VDC) - 10mA (24
VDC)
Not required. Integrated
failsafe element (internal fuse)
7 ...32 Vdc
Controlled DC voltage
0.2 V
2
10 A
1 ...10A
via Blink code Led
Yes
No
< 0.5 sec.
>32 Vdc
50.000 uF
0.5 KV
97%
1.5W (Nominal Operation)
0.9 W (No Load operation)
switch-off after approx. 5 s
switch-off after approx. 1 s
switch-off after approx. 0,1 s
switch-off after approx. 0,03 s
switch-off after approx. 0,03 s
- Manual Reset
- By Press Button
- 5 sec max. (Hover load / Short
Circuit)
16A per output (not replaceable)
Max 32 Vdc (on Load Circuit)
Three-color LED per output:
- green LED for "Output switched
through"
- Red LED for "Output switched off
manually"
- Red LED Blink for "Output
switched off due to overcurrent"
- Orange LED: Verify and Config
AUX1: connection 2 pin AMP
1: as ADELBus for Driving,
Monitoring, Configuring
2: Out Alarm for For SwitchOff
Output
- Common Signaling for
disconnection Last Output
- Single Channel: Current, set current
threshold, Status On/Off
- Reason of Output disconnection
2
1 Screw Type
0.2 - 2.5 mm
(24 – 12 AWG);
1 Screw Type
0.6 - 0.8 Nm
1 Screw Type
AUX1: connection 2 pin AMP
-25 up to+60°C (>60°derating
2.5%°C)
-25 up to +70 °C
-40 up to +85 °C
95 % to 25 °C (acc. to IEC 60721)
<15 Hz, amplitude  2.5mm
<15Hz-150Hz, 2.3G 90 min.
No restrictions
Via Luigi Barchi 9/B – Reggio Emilia 42124 – Italy
Tel. +39 0522 345518 – Fax +39 0522 345551 –
General Data
Protection Class (EN/IEC
60529)
Reliability: MTBF IEC 61709
Protection class
Housing material
Foot latch material
Screw type connection
Dimension (w-h-d) mm
Weight
8
Norms
Immunity and Emission
The CE mark in conformity to EMC 2014/30/EU: Electromagnetic
Compatibility Directive; 2014/35/EU: Low Voltage Directive; ROHS
2011/65/EU: Restriction of the use of certain Hazardous Substances in
Electrical and Electronic Equipment (RoHS), as amended by
2015/863/EU
•
EMC Immunity: EN61000-6-2
•
EMC Emission: EN61000-6-3, EN 55022 ClassB
Electrical Safety for mounting
According to:
•
Electrical Equipment for Machinery EN 60204
•
Electrical safety (of information technology equipment)
IEC/EN EN62368-1.
•
Safety
requirements
measurement, control and Laboratory use IEC/EN 61010
9
Accessory
•
RTConn: connector cable for the connection to AUX1. It is
possible drive the device through the ADELBus network.
www.adelsystem.com
Instruction Manual MRF102_7.docx
IP20
> 700.000 h (Automatically Switch
Off Beck Light after 30 sec)
III
Polycarbonate
Plastic POM
(24 – 12 AWG
2
0.2 - 2.5 mm
0.6 - 0.8 Nm
18 x 90 x 61
0.1 kg approx.
for
electrical
equipment
Page 3
for