Dynabrade 52557 Manual - Página 4

Navegue en línea o descargue pdf Manual para Herramientas Dynabrade 52557. Dynabrade 52557 4 páginas. Horsepower tools

Imprimir página
Motor Assembly/Disassembly Instructions – .55 Hp
3. With a firm hold on the 02097 Housing, use a 34 mm or an adjustable wrench to turn the 01461 Lock Nut counterclockwise to loosen the 02097 Housing
from the valve housing.
4. Orient the throttle lever to the operators desired grip and positioning. Note: Allow for additional rotation of the 02097 Housing as the 01461
Lock Nut is tightened.
5. With a firm hold on the 02097 Housing to reduce its rotation, use a 34 mm or an adjustable wrench to tighten the 01461 Lock Nut.
Torque to 45 N•m.400 in.- lbs.
Important: Carefully perform this procedure so as not to entirely separate the 02097 Housing from the valve housing. Loosen the 01461 Lock Nut only
enough to make the desired throttle lever adjustment. Motor should now be tested for proper operation at 90 PSIG. If motor does not operate properly or
operates at a higher RPM than marked on the tool, the tool should be serviced to correct the cause before use. Before operating, place 2-3 drops of
Dynabrade Air Lube (P/N 95842) directly into air inlet with throttle lever depressed. Operate tool for 30 seconds to determine if tool is operating properly and
to allow lubricating oils to properly penetrate motor
Loctite
is a registered trademark of Loctite Corp.
®
Dynaswivel
Swivels 360° at two locations which
allows an air hose to drop straight to
the floor, no matter how the tool is held.
•
94300: 1/4" NPT.
Dynabrade Air Lube
•
Formulated for pneumatic equipment.
•
Absorbs up to 10% of its weight in water.
•
Prevents rust and formation of sludge.
•
Keeps pneumatic tools operating longer
with greater power and less down time.
95842: 1pt. (473 ml)
95843: 1gal. (3.8 L)
96522 Motor Tune-Up Kit
•
Includes assorted parts to
help maintain and repair motor.
96232 (#2) Arbor Press
•
This arbor press is ideal for the disassembly
and assembly of air motors.
96346 Bearing Separator
•
Use the separator to remove gears
and bearings.
95262 – 14 mm open-end
Used On Models 52557, 57127,
52558 & 52580.
96506 – 1/8" Pin Wrench
Used On Model 57127.
Visit Our Web Site: www.dynabrade.com
DYNABRADE, INC., 8989 Sheridan Drive • Clarence, NY 14031-1490 • Phone: (716) 631-0100 • Fax: 716-631-2073 • International Fax: 716-631-2524
DYNABRADE EUROPE S.àr.l.,
© DYNABRADE, INC., 2002
Optional Accessories
®
95263 – 17 mm open-end
Used On Model 52515,
52516 & 52518.
96507 – 1/8" Pin Wrench
Used On Model 52515,
52516 & 52518.
Zone Artisanale • L-5485 Wormeldange—Haut, Luxembourg • Telephone: 352 76 84 94 1 • Fax: 352 76 84 95 1
Wrenches
95281 – 19 mm open-end
Used On Model 52280 & 52518.
(continued)
57092 Repair Collar
•
Specially designed collar for use in vise to
prevent damage to motor housing during
disassembly/assembly.
52296 Repair Collar
•
Specially designed collar for use in vise to
prevent damage to valve body during
disassembly/assembly.
56058 Lock Ring Wrench
•
Lock Ring Tool has a 3/8 in. square socket
for use with 3/8 in. drive; breaker bar,
ratchet head, or torque wrenches.
57091 Bearing Press Tool
•
Use with a #2 arbor press to achieve
accurate press of bearings and motor parts.
96525 Tool Repair Kit
•
Includes special tools for proper
disassembly/assembly of the tool.
•
Includes all above listed tools.
95823 – 21 mm open-end
Used On Model 52515 & 52516.
DYNABRADE
®
PRINTED IN USA