Dynabrade 52836 Seguridad, funcionamiento y mantenimiento - Página 2
Navegue en línea o descargue pdf Seguridad, funcionamiento y mantenimiento para Taladro Dynabrade 52836. Dynabrade 52836 9 páginas. Pistol grip drill; .4hp/rear exhaust/1/4" drill chuck
Imprimir página
Accessory Selection:
• Before mounting a drill accessory only use a drill accessory that is suitable for the RPM and drill chuck size, visually inspect for defects. Do not use defective accessories.
• Use only recommended accessories. See back page of manual and Dynabrade catalog.
• Only use recommended fittings and air line sizes. Air supply hoses and air hose assemblies must have a minimum working pressure rating of 150 PSIG (10 Bars) or
150 percent of the maximum pressure produced in the system, whichever is higher. (See tool Machine Specifications table.)
Warning: Always wear eye protection. Operator of tool is responsible for following: accepted eye, face, respiratory, hearing and body protection.
Warning: Keep hand and clothing away from working end of the air tool.
Warning: Unexpected tool movement or breakage of inserted tool may cause injury.
Warning: Be sure that any loose clothing, hair and all jewelry is properly restrained.
Caution: Hand, wrist and arm injury may result from repetitive work, motion and overexposure to vibration.
Caution: Release throttle in case of an interruption of the energy supply.
Caution: Use only recommended lubricants.
• Secure inlet bushing on air tool with a wrench before attempting to install the air fitting to avoid damaging housing assembly.
• BEFORE MOUNTING A DRILL ACCESSORY, after all tool repairs and whenever a drill is issued for use, check tool RPM (speed) with tachometer with air pressure set at
90 PSIG while the tool is running. If tool is operating at a higher speed than the RPM marked on the tool housing, or operating improperly, the tool must be serviced and
corrected before use.
Warning: Disconnect air supply before removing inserted drill bit.
• Open chuck jaws wide enough to install drill bit. Be sure the bit shank and chuck jaws are clean. Dirt particles may prevent the drill bit from lining up properly.
• Insert the drill bit into the chuck. Center the drill bit in the chuck jaws and lift it about 1/16" off the bottom. Tighten the chuck jaws by hand to align the drill bit.
• Place the chuck key in each of the three holes in the chuck, turning it clockwise. Tighten securely.
Warning: Remove chuck key before turning the tool on.
• Connect air tool to air supply. Be careful NOT to depress trigger in the process. Do not expose air tool to inlet pressure above 90 PSIG or (6.2 Bars).
Caution: After installing the drill bit, before testing or use and/or after assembling tool, the Pistol Grip Drill must be started at a reduced speed to check for good balance.
Gradually increase tool speed. DO NOT USE if tool vibration is excessive. Correct cause, and retest to insure safe operation.
• To remove the drill bit, insert the chuck key into the holes in the chuck and turn counterclockwise.
Bit Selection:
• Use sharp drill bits. Sharp drill bits are less likely to bind when drilling. Use the proper drill bit for the job.
• Check the information on the drill bit's packaging for proper usage. Do not use drill bits larger than the rated capacity of the drill.
Warning: Air tools are not intended for use in explosive atmospheres and are not insulated for contact with electric power sources.
Warning: Always work with firm footing, good posture and proper lighting.
Warning: Drilling certain materials can create explosive dust. It is the employer's responsibility to notify the user of acceptable dust levels.
Caution: If the drill bit binds, the drill will suddenly react in the opposite direction of the rotation of the bit. The operator should prepare for a sudden reaction by holding the tool securely.
• Driving larger drill bits at the high speeds will increase the chance of reaction.
• Avoid drilling warped, wet, knotty, and pitchy materials if possible.
• When removing the drill bit from the tool avoid contact with the skin and use proper protective glove when grasping the drill bit. Drill bits may be hot after prolonged use.
• Make sure that work area is uncluttered, and visitors are at a safe range from the tools and debris.
• A moving drill bit that snags or catches within the work piece may cause tool to stop unexpectedly or move erratically, which may cause injury.
• Use a vise or clamping device to hold work piece firmly in place. Do not apply excessive force on tool or apply "rough" treatment to it.
• Ensure that sparks and debris resulting from work do not create a hazard.
• This tool is rear exhaust. Exhaust may contain lubricants, vane material, bearing grease, and other materials flushed through the tool.
• Some materials contain chemicals which may be toxic. Take caution to prevent dust inhalation and skin contact. Follow material supplier safety data.
• Certain materials can cause sparks which can cause fires or explosions. It is the user's responsibility to make sure the work is done on spark free materials.
Report to your supervisor any condition of the tool, accessories, or operation you consider unsafe.
Regulator
Filter
90 PSIG
(6.2 Bar)
• Dynabrade Air Power Tools are designed to operate at 90
PSIG (6.2 Bar/620 kPa) maximum air pressure at the tool
inlet, when the tool is running. Use recommended regulator
to control air pressure.
• Ideally the air supply should be free from moisture. To
facilitate removing moisture from air supply, the installation
of a refrigerated air dryer after the compressor and the
use of drain valves at each tool station is recommended.
SAFETY INSTRUCTIONS CONTINUED
OPERATING INSTRUCTIONS
DRILL ACCESSORY MOUNTING INSTRUCTIONS
Air System
Lubricator
LUBRICATOR SETTING
1 DROP/MIN.
20 SCFM
Closed Loop Pipe System
(Sloped in the direction of air flow)
To Tool Station
Regulator
Filter
Ball
Valve
Drain
Valve
Drain
Valve
90 PSIG MAX
Air Tool
2
Air Flow
Refrigerated
Lubricator
➤
Ball
Valve
Air Hose
(6.2 Bar)
Air Flow
Air Compressor
and Receiver
Drain Valve
Air Dryer