ADEMCO ADEMCO VISTA-20PSIA Manual de instalación rápida

Navegue en línea o descargue pdf Manual de instalación rápida para Sistema de seguridad ADEMCO ADEMCO VISTA-20PSIA. ADEMCO ADEMCO VISTA-20PSIA 2 páginas. Ademco vista series security system
También para ADEMCO ADEMCO VISTA-20PSIA: Manual de programación (17 páginas), Manual del usuario (20 páginas), Manual de instalación rápida (2 páginas), Manual de instalación rápida (2 páginas), Manual rápido (2 páginas)

Imprimir página

ADEMCO ADEMCO VISTA-20PSIA Manual de instalación rápida

FOR DOCUMENTATION AND ONLINE SUPPORT: http://www.security.honeywell.com/hsc/resources/MyWebTech

Mount the Control.

1. Mount the control cabinet to a sturdy wall in a clean, dry area, which is not readily accessible to the

general public, using fasteners or anchors (not supplied) with the four cabinet mounting holes.

2. Remove cabinet door, then remove the lock

knockout from the door. Insert the key into the lock

CHECK

POSITION

3. Position the lock in the hole, making certain that the

LOCKED

latch will make contact with the latch bracket when

the door is closed. When correctly positioned, push

the lock until the snap tabs hold it securely.

The cabinet can be secured without a lock by

using 2 screws in the cover' s edge.

CABINET DOOR

4. Before installing the cabinet' s contents, remove

the cabinet knockouts needed for wiring entry.

Installing the Cabinet Lock

5. Mount the PC Board. Refer to the diagram below. If mounting an RF Receiver inside the cabinet,

remove the receiver board from its case, then insert the top of the board into the slots at the top of the

cabinet. Install the control board below the receiver board using the clips and screws provided. Insert

grounding lugs into the left-hand terminals of the antenna blocks and secure them with the screws

provided. Insert the receiver' s antennas into the blocks' right-hand terminals, and tighten the screws.

CIRCUIT

BOARD

CABINET

DETAIL A

SIDE VIEW

OF BOARD SUPPORTING

SLOTS

INSERT THE TOP OF THE

(PROVIDED) ON THE RAISED CABINET TABS.

CIRCUIT BOARD INTO THE

SLOTS AT THE TOP OF THE

CABINET

Mounting the PC Board

Connect the Transformer & Battery.

1321 Transformer (1321CN in Canada)

• Do not plug the transformer into the AC outlet until all wiring connections to the control are complete. As

a safety precaution, always power down the control when making such connections.

1361X10 Transformer

(required if using Powerline Carrier devices)

1. Splice one end of a 3-conductor cable to the wire ends of the SA4120XM-1 cable.

2. Connect the SA4120XM-1 cable plug to the 8-pin connector on the control.

3. Connect the other end of the 3-conductor cable to the 1361X10 Transformer.

Canadian Installations: For Powerline Carrier Devices, use the PSC04 X-10 Interface and trigger pins.

Battery Connections

• After all connections to the control are completed and after AC power has been applied, connect the

red and black flying leads on the control board to the battery.

• IMPORTANT: This control will not power-up on battery alone (AC power must be applied). However,

once the system is powered up, it will operate on battery if AC is lost.

UL For UL installations and Residential fire installations, refer to the chart below for the correct battery

size required to meet the mandatory standby time.

CALIFORNIA STATE FIRE MARSHALL (CSFM) AND UL RESIDENTIAL FIRE

24-HOUR BATTERY BACKUP REQUIREMENTS

The California State Fire Marshal and UL have regulations which require that all residential fire alarm

control panels must be provided with a backup battery which has sufficient capacity to operate the panel

and its attached peripheral devices for 24 hours in the intended standby condition, followed by at least 4

minutes in the intended fire alarm signaling condition. This control panel can meet these requirements

without using a supplementary power supply, provided that the panel's auxiliary power and bell output

currents are limited as listed below.

OUTPUT LIMITATIONS AND REQUIRED BATTERIES

OUTPUT CURRENT LIMITS

BATTERY INFORMATION

Current Total

Max. Aux.

Battery Capacity

Recommended Battery

Current

(Amp/Hrs)

(Yuasa Model No.)

600mA

45mA

4AH

NP4-12 (or ADEMCO 467)

maximum total

160mA

7AH

NP7-12

of auxiliary

200mA

8AH

NP4-12 (two) ‡

power plus bell

425mA

14AH

NP7-12 (two) ‡

output currents

500mA

17.2AH

NPG18-12

‡

NOTE: Use two batteries, connected in parallel. Obtain an Ademco Battery Harness Kit SA5140-1. (Both batteries will

fit inside the cabinet.)

K5305-1QGV1 5/09 Rev. A

Connect Devices, Zones, Sounder, and Phone Line.

Refer to the Wiring Diagram on the reverse side for connection information. NOTE: This system uses a range of reserved addresses for each type of device.

1. Connect keypads and other addressable devices to the ECP terminals 4-7.

Refer to the wiring chart below for wire sizes and maximum wire run lengths.

PUSH

ON LOCK

UNTIL IT

Wire Chart For Devices Drawing Aux Power From The Control (12V+ & 12V–)

SNAP

IS SEATED

TAB

SECURELY

Wire

TOTAL CURRENT OF ALL DEVICES CONNECTED TO A SINGLE WIRE RUN

PUSH

Size 50 mA or less

#22

900ft (274m)

#20

1400ft (427m)

SNAP

TAB

#18

1500ft (457m)

UNLOCKED

#16

1500ft (457m)

BOTTOM

STEP 1

STEP 2

The length of all wire runs for both partitions combined must not exceed 1500 feet (457m) when unshielded quad

conductor cable is used (750 feet if shielded cable is used).

Standard Keypads (6150 / 6160 series)

• Keypad addresses range from address 16-23. Set each keypad's address accordingly.

NOTE: Address 16 is reserved for the first keypad and is always enabled in the control.

• Use data fields ∗190-∗196 to enable keypads and set their sounding options.

Expander Modules (4219, 4229)

• Connect desired field wiring to the module's zone terminals.

CIRCUIT

CABINET

BOARD

• Expander module addresses range from 07-11. Set each module's DIP address accordingly.

• Use ∗56 Menu mode to program zone characteristics.

Touchscreen Keypads (6270 / 6271 series, 8132 series; V20P = up to 4; V15P = up to 2)

DETAIL B

SIDE VIEW

• Use of touchscreen keypads is independent from and in addition to the eight (8) standard keypads.

OF MOUNTING CLIPS

• Set each touchscreen's address accordingly (1, 2, 5, 6; see table on back) and enable in field ∗189.

HANG TWO SHORT MOUNTING CLIPS

• Make sure the auxiliary current drain is within the control's limitation. Otherwise use an external

SECURE THE BOARD TO THE

CABINET WITH THE ACCOMPANYING

power supply to power the touchscreen keypads.

SCREWS

cb_mount-001-V1

RF Receiver (5881, 5883, RF Keypad)

• 5881L / 5882L = up to 8 RF zones; 5881M / 5882M / 6150RF = up to 16 RF zones

5881H / 5882H / 5883 / 6160RF = up to system maximum RF zones

• Set the receiver's address to 00 using the module's DIP switches.

• If using wireless keypads, set field ∗24 RF House ID Code appropriately.

If receiver is mounted remotely, note the following:

• Do not locate the receiver or transmitters on or near metal objects. This will decrease range and/or

block transmissions.

• Do not locate the RF receiver in an area of high RF interference (indicated by frequent or

prolonged lighting of the receiver's LED; random flicker is OK).

• Do not locate RF receiver closer than 10 feet from any keypads.

Program the Control.

Refer to the Programming Guide to program the control.

(

The control can also be programmed via the Compass Downloader.)

1. Enter Programming Mode: installer code + 8-0-0.

2. Change the default Installer Code using field ∗20.

3. Enter the appropriate central station phone numbers and account numbers.

4. Program the system data field options as desired.

4. Use the various menu modes to program zones, relay outputs, descriptors, etc.

5. If AVS system is installed, use the appropriate AVS Quick Program Command.

6. Program Schedules (if used): Master code + [#] + 64

7. Enable RF button keyfobs (if used) and assign to user numbers accordingly.

8. Show the Master user how to change the default Master code:

master code + [8] + 0-2 + new code + new code again

Test the System.

Sniffer Mode Test: To verify that all transmitters have been properly programmed, disarm all partitions.

1. From a keypad in partition 1, enter Installer code + [#] + 3. All programmed transmitters are displayed.

2. Fault all transmitters in turn. The display clears each transmitter as a signal is received.

3. Exit Sniffer mode: Installer code + 1 (OFF). Mode does not automatically expire; you must exit manually.

System Test

1. Disarm the system and close all protected windows, doors, etc.

2. Enter the Installer code + [5] (TEST), then press 0 = walk. (Option 1 = Dial checks phone line integrity.)

3. Listen. The external sounder should sound for about 1 second then turn off.

4. Fault all zones in turn and listen for three beeps from the keypad. ID of each faulted point should

appear on the keypad display. The display clears when the zone is restored.

5. Test all smoke and CO detectors following the manufacturer' s instructions and check the display.

6. When all zones have been checked and are intact (closed), there should be no zone identification

numbers displayed on the keypad.

7. Exit test mode: security code + [1] (OFF).

(see instructions K5305-1V7 or higher)

100 mA

300 mA

500 mA

600 mA

450ft (137m)

150ft (46m)

90ft (27m)

75ft (23m)

700ft (213m)

240ft (73m)

140ft (43m)

120ft (37m)

1100ft (335m)

350ft (107m)

220ft (67m)

170ft (52m)

1500ft (457m)

550ft (168m)

350ft (107m)

270ft (82m)

These instructions apply to the following Honeywell security systems:

ADEMCO VISTA-20P, VISTA-20PSIA, VISTA-20PCN, VISTA-15P, VISTA-15PSIA, VISTA-15PCN

Features and procedures apply to all, except where differences are noted.

VISTA-20PSIA and VISTA-15PSIA are certified SIA-compliant controls that meet SIA specifications for

False Alarm Reduction.

Relay Modules (4204)

• Connect desired field wiring to the module's relay contact terminals.

• Relay module addresses range from address 12-15.Set each module's DIP address accordingly.

• Use ∗79 / ∗80 Menu modes to map each device address and define output functions.

Communication Device (7847i, 7845GSM, 7845i-GSM, GSMV)

• Set the communication device to address 03.

• Use ∗29 Menu mode to enable and program the device.

AVS System

• If used, follow the installation instructions provided with the module.

• Connect the AVS module to the control's ECP terminals and connect all other ECP devices to the

AVS module's ECP terminals.

• Set the AVS address using its DIP switches: V15P = 08; V20P = 11

• Use the desired AVS Quick Program Command to set pre-defined options:

installer code + [#] + 0 + 3: enable AVS operation

installer code + [#] + 0 + 4: enable AVS and enable panel sounds on AVST speaker

• Use field ∗55 Dynamic Signaling Priority to select the desired reporting paths.

2. Connect hardwire zones to the appropriate zone terminals 8-20.

3. On-Board Trigger Connections

• Connect field wiring to the appropriate trigger pin using the SA4120XM-1 cable (if using 1361X10

transformer) or the 4-wire cable supplied (N4632-4).

• Trigger outputs are normally high, and go low upon programmed condition (can be set inverted).

• Use ∗79/∗80 Menu modes to program the trigger outputs.

• Output 17 (pin 1) = supports up to 100mA max; Output 18 (pin 5) = supports up to 20mA max

4. Install Wireless Zone Transmitters.

• Use ∗56 Menu mode to program wireless zones and enroll the transmitters.

• Use the Go/No Go Test mode to verify adequate signal strength from each transmitter location:

Enter Installer code + [#] + 4, then fault each transmitter and listen for 3 beeps at the keypad and

the zone display. Exit mode: user code + 1 (OFF).

5. Connect the external sounder to terminals 3 and 4.

• If supervised output desired, see Sounder Supervision wiring diagram on reverse side, and set field

∗91 Option Selection for Bell Supervision.

6. Connect the phone line using terminals 21-24.

• Use an RJ31X jack as shown in the diagram on reverse side.

Major Features and Capacities

Feature

VISTA-20P

Partitions

2 plus common area

Zones

48 plus 16 keyfob zones for

total of 64 zones:

• 8 hardwired zones (1-8)

• Up to 40 additional wired

zones (9-48) using up to 5

4219/4229 modules

• Up to 40 wireless zones

(5800 series; zones 9-48)

• 4 configurable zone types

Security Codes

Schedules

Keypad macros

Event Logging

100

Paging

Keypads

Touch Screen Devices

4219, 4229

4204

Output Relays / X-10 devices

On-Board Triggers

Output Functions

WARRANTY INFORMATION

For the latest warranty information, please go to:

www.honeywell.com/security/hsc/resources/wa

VISTA-15P

not partitioned

32 zones plus 8 keyfob zones

for total of 40 zones:

• 6 hardwired zones (1-6)

• Up to 16 additional wired

zones (9-24) using up to 2

4219/4229 modules

• Up to 26 wireless zones

(5800 series; zones 9-34)

• 2 configurable zone types

2 Corporate Center Drive, Suite 100

P.O. Box 9040, Melville, NY 11747