EMERGENT EYE Instrucciones de instalación y uso - Página 2

Navegue en línea o descargue pdf Instrucciones de instalación y uso para Mobiliario interior EMERGENT EYE. EMERGENT EYE 2 páginas. Cable managed desks

Imprimir página

H. Cable Ties

K. No. 8 x ½" Self-Tapping Screw

J. No. 6 x ½" Countersunk Woodscrew

DIAGRAM C

It is important to bear in mind that there

is always some risk involved in handling

electrical equipment so all reasonable

care must be taken in following these

instructions to minimise the risk.

We recommend that a suitable qualified

electrical engineer is used to install and

test the power accessories and earthing

provision. The cable management is of

earthed construction. Maximum load 50Hz

13 amp. Maximum load per socket 5 amp.

For safety and compliance with

BS.6396:2008 the following socket

configurations and numbers must not be

exceeded. (30Ma R.C.D 13 AMP mains

plug optional) SEE DIAGRAM B.

On completion or re-configuration of

the electrical system within the furniture

the following electrical tests must be

carried out. It is recommended that these

tests are repeated at least annually for

continued safety.

Continuity & Polarity.

A test of all conductors, including the

protective earth conductor, Shall be made

to verify their continuity and correct polarity.

This test shall include the supply cord

and plug. The electrical system shall be

inspected to ensure that any fuses and any

single pole switches fitted are connected

only in the live conductor.

Insulation Resistance.

The insulation resistance of completed

electrical installations shall be tested using

a 500V D.C. test supply. The measured

resistance shall be not less than 1 M ohm.

Tests shall be made between conductors

and also to earth of the supply cable. The

duration of each test shall be not less than

5 seconds.

Emergent Crown Ltd, Unit 5, Browmills Industrial Estate,

Brighouse Road, Hipperholme, Halifax HX3 8EF

t.01422 349119 [email protected] w.www.emergent-crown.co.uk

Linking Plate

DIAGRAM D

Note – Neon indicators shall be removed

from the circuit before carrying out this test

between conductors by switching off the

socket outlet. Where luminaries contain

sensitive electronic components, these

shall be disconnected prior to the test (see

713-04-04 of BS 7671)

Earth Continuity.

Earth connections of the installed socket

outlets and the accessible metal parts of

the earthed office furniture shall be tested

by passing a current of not less than 1.5

times the rating of the supply plug fuse

and no greater than 25 A, derived from

an a.c source with a load voltage not

exceeding 12 V. The tests shall include

the supply cord and shall be carried out

between the earth pin of the supply plug,

the earth connections of the installed

socket outlets and where applicable the

accessible metal parts of the earthed

furniture. The duration of the tests shall be

for a period 5 s and 20 s. The resistance

shall not exceed 0.1 Ohm.

Trunking Assembly

To Desking

SEE DIAGRAM A. Hang the trunking

(A) over the modesty panel. Fasten to

the modesty panel with 2 off No. 8 x ½"

woodscrews (B). Fasten the trunking end

cap (C) to the end of the trunking with 2 off

M4 taptite screws and serrated washers (D

& E). Fasten the leg riser (F) to the trunking

with 2 off M4 taptite screws and serrated

washers (D & E). Fasten the leg riser to

the modesty panel with 1 off No. 8 x ½"

woodscrew (B). Fasten the leg riser cover

(G) to the leg riser with 2 off M4 taptite

screws (D).

DIAGRAM E

Cable Routes.

Where desks are linked together the best

position for cables to enter is either at

the beginning or end of a configuration.

Cables will normally enter desks at the

bottom of the leg riser and be anchored

by the cable clamp provided. Where

cables run from the building out to the

desks, these exposed lengths [from the

plug to the cable entry point or appliance

inlet connector] should be as short as

possible and must not exceed 2 metres.

Cables should be positioned so as not

to be a hazard to people walking by. Use

cable ties (H – SEE DIAGRAM C) in the

trunking slots to segregate power and

data cables. Run power and data cables

in separate channels in the leg riser plastic

channel. Where cables run from desk to

desk, these desks must be securely linked

together using the plates provided.

(SEE DIAGRAM D).

Power Socket

Installation

SEE DIAGRAM E. First decide on the

position of the socket inside the horizontal

face of the trunking, then fasten through

the socket lugs through clearance holes in

trunking into the modesty panel with 2 off

No. 6 x ½" csk woodscrews (J ). Connect

the socket earth lead to a nearby marked

earth point with 1 off No. 8 x ½" self-

tapping screw (K).