Automatic Technology Australia Securalift GDO 2v4 Instrucciones de instalación y manual del usuario - Página 3

Navegue en línea o descargue pdf Instrucciones de instalación y manual del usuario para Abrepuertas de garaje Automatic Technology Australia Securalift GDO 2v4. Automatic Technology Australia Securalift GDO 2v4 19 páginas.

Imprimir página
Your
Securalift Automatic
Garage
Door
Opener
has many
features
which you
will
appreciate.
The
components
and materials used in
this
Automatic Opener are
of
the
latest
technology
and
highest
qualrty. Below are listed some
of
these features
OPERATION
To
operate
the door simply
press
the
hand held transmitter
or
the wall
mounted transmitter
or
optional
wall
switch
for two
seconds and
the
door
will
automatically open or
close.
The door can
be
stopped
during
an
opening or closing cycle
by
pressing again.
The
next
actuation
will
move
the door in the
opposite
direction.
CODE HOPPING
Every time a transmission
is
made
from
the
Remote
Transmitter a new
security code
is
generated.
The
number of possible
code
combinations nms into the billions.
This greatly
enhances
security
of
the
system.
Code 'Grabbing'
is
made
a
thing
ofthe
past.
ISS
(INTELLIGENT SAFETY
oBSTRUCTTON SYSTEM)
While the door
is
doing
a
closing
cycle and
if
it
should
hit
an obstacle
or be
restricted
in
scme manner,
it
will
automatically reverse.
The
amount
of
force
the
door
should
encounter before reversing,
is
automatic4lly adjudted
by the
doors
control
system,.
during
the
initial
installation
of the
automatic door
opener.
The door also
if
restricted
whilst
opening
will
stop.
The Safety
Obstruction Force
shou
ld
be
checked
at
least once
a month.
See
installation manual
for instructions
SECURITY CODE STORE
The
Opener uses state
of the
art
technology in storing your
selected
Transmitter Security
Code.
Up
to
27
different codes can
be
stored
in
the Openers
memory
device.
To
store
any code simply press
and
hold the Code Store button on
the
Opener
and
press
the
Transmitter
button twice. Each
or
all
codes
can
be deleted and
changed
at
any time.
The codes can also
be stored from
a
remote
location.
OVER LOAD INDICATOR
When
the
maximum opening
and
closing capacity
of
the
Opener
is
exceeded
the
Courtesy
Light
and
Overload
LED
will
flash
to
indicate
that an Overload
has
occurred.
SER}'ICE INDICATOR
The Opener has a Service indicator.
When
the
Overload
LED
lights
up
continuously
it
means
that the opener
and
,or
garage
door
needs a service.
AUTO COURTESY
LIGHT
The
Courtesy
Light
on the
Opener
comes on
automatically whenever
tle
door is activated
to do
an opening or
closing cycle. The Light can also
be
switched
on
and
off
without
operating
the
door. This
is
done
by
pressing
the button
on
the Hand
Held
Transmitter Wireless
Wall
Mounted
Transmitter which has being
stored
as
the light code, or by
pressing
the
light
button
on the Wall
Switch
(optional). The light
will
stay
m
for
approximately three minutes
then
go
off..
This
time
is also adjustable.
CAS (COLOUR ASSISTED
SETTINGS)
To
make
the
installation
of
the
Automatic Opener more user
friendly
Automatic
Technology
Australia
developed
the CAS (Colour
Assisted
Settings) system.
This unique
system
allows
for all
the
Open and
Close
adjustments and settings
to
be colour
coordinated,
Red
for
Close
and
Green
for
Open.
The
colour
coordination make
its
easier
and
quicker
for the
user
or
installer to
complete
the installation.
OPEN AND CLOSE DRTVE
BUTTONS
Another feature
developed
by
Automatic Technology Australia in
aiding
in
the
rnstallation
of
the
opener are
the Ope,
and
Close
Drive
Buttons. These buttons
are
used
to help
set
the
open
and close
limit
positions.
A quicker
sefring
time and
a
more precise
limit
position can be achieved
usrng
this
system.
INITIALISATION
The
Reset
button
on
the
!
or
Opener
is
used
to
initialise
or
re-initialise the obstruction
settings
and door travel
counts.
See
installation manual
for instructions.
AUTO CLOSE MODE
The
Opener can be programmed
to
automatically close
after an
open
cycle. The
Auto
Close
time
is
adjustable.
A
Photo Electric
Beam
must
be
installed
if
this
mode
is
selected.
AUTO
RT]N
TIME
If
the Motor is
left
running
in
the
Opener
for
any
reason
the
Auto
Run
Time
will
tum the motor
off
after
thirty
seconds.
PHOTO ELECTRIC BEAM
(oPTroNAL)
v
The
Opener
has
an
input
for
a
Photo
Electric Beam
to
be
connected
for
extra
safety
p
rotection.
MANUAL OPERATION
The
Opener
is
equipped
with
a
unique Manual Disengaging Device.
If
the
power
to
the
Opener
is
disrupted
for
any
reason
the
door
can be
put into Manual Mode
by
pulling down on the
string
handle
on an angle towards the door,
then
releasing.
This
will
allow you
to
manually open or
close
the door. To
re-engage
pull the string at
an angle
away
from the door then
release.
Page
I