2gig Technologies GC3 Manual de inicio rápido

Navegue en línea o descargue pdf Manual de inicio rápido para Control Panel 2gig Technologies GC3. 2gig Technologies GC3 2 páginas. Lte cellular radio module
También para 2gig Technologies GC3: Manual (4 páginas)

Imprimir página

2GIG

GC3 Security & Automation System

2GIG-LTEV-A-GC3 | LTE Cellular Radio Module

10015237 B | Proprietary & Conﬁ dential

Installing the GC3 LTE Cellular Radio Module

The 2GIG GC3 LTE Cellular Radio Module is a snap-in unit providing the GC3

Security & Automation System with communication to the Central Station for

alarm signaling and delivering (Over-the-Air) OTA ﬁ rmware updates to the GC3

Panel. It also provides connectivity to the Remote Service Provider and 2-way

voice communication.

The module includes a built-in antenna to provide a consistently strong

communications signal. An optional external antenna Model 2GIG-ANT5XL-GC3

is also available.

Box Contents

Verify that the package includes the following:

—GC3 LTE Cellular Radio Module

Figure 1 GC3 LTE Cellular Radio Module

Install/Replace the Cellular Radio Module

To install/replace the Cellular Radio Module into a system that is completely

powered OFF:

Open and remove the hinged door from the GC3 Control Panel.

Figure 2 Cellular Radio Module—Hinged Door

If you are replacing a module, pull the tab to remove the Cellular Radio

Module. Otherwise, skip this step.

Insert the new GC3 Cellular Radio Module until it clicks in place.

Figure 3 Inserting GC3 Cellular Radio Module

Replace the hinged door.

(Optional) Install the lock on the Cellular Radio Module bay door. See

"(Optional) Lock/Unlock the Cellular Radio Module Door."

Power up the system and wait 30 to 40 seconds for the Control Panel

to recognize the Cell Radio Module.

After installing the Cellular Radio Module, go to the Installer Toolbox

> System Conﬁ guration > Radio Test. Then tap Start Radio Test.

When the test reads "Success", tap Done.

PRINTER'S INSTRUCTIONS:

INSTR,INSTL, 2GIG-LTEV-A-GC3 - P/N: 10015237 B - INK: BLACK - MATERIAL: 20 LB MEAD BOND

SIZE: 8.500" X 11.000" - TOLERANCE: ± .125" - SCALE: 1-1 - SIDE 1 OF 2

To install/replace the Cellular Radio Module into a system that is powered ON:

From the Home screen, go to System Settings > Cell Radio Swap.

Tap Begin.

Open and remove the hinged door from the GC3 Control Panel.

If you are replacing a module, pull the tab to remove the Cellular Radio

Module. Otherwise, skip this step.

Insert the new CG3 Cellular Radio Module until it clicks into place.

Replace the hinged door.

(Optional) Install the lock on the Cellular Radio Module bay door. See

"(Optional) Lock/Unlock the Cellular Radio Module Door".

Tap Done.

Tap Radio Test and then tap Start Radio Test.

10. When the test reads "Success", tap Done.

(Optional) Lock/Unlock the Cellular Radio Module Door

The Cellular Radio Module ﬁ ts into the bay on the side of the GC3 Panel and

features a built-in door lock under the faceplate. The Control Panel ships with

the door-lock screw in the UNLOCK position. To limit the possibility of someone

removing the door, installers have the option of moving the screw to the LOCK

position.

To lock and unlock the Cellular Radio Module door:

Use your ﬁ ngertips or carefully insert a screwdriver at the edge of the

faceplate. Then gently pry the faceplate from the chassis.

Figure 4 GC3 Panel—Removing Faceplate

Remove the door locking screw from the UNLOCK position on the right.

Figure 5 GC3 Panel—UNLOCK position

Install the door locking screw into the LOCK position on the left. This

locks the hinged door on the GC3 Control Panel.

Figure 6 GC3 Panel—LOCK position

Snap the faceplate back on the GC3 Control Panel.